Abstract:Purpose To fabricate a selective laser melting (SLM)-processed AlSi10Mg part with almost full density and free of any apparent pores, this study aims to investigate the effect of ambient argon pressure and laser scanning speed on the particles splash during the AlSi10Mg powder bed laser melting. Design/methodology/approach Based on the discrete element method (DEM), a 3D model of random distribution of powder particles was established, and the 3D free surface of SLM forming process was dynamically tracked by the volume of fluid, where a Gaussian laser beam acts as the energy source melting the powder bed. Through the numerical simulation and process experimental research, the effect of the applied laser power and scanning speed on the operating laser melting temperature was studied. Findings The process stability has a fundamental role in the porosity formation, which is process-dependent. The effect of the processing conditions on the process stability and the resultant forming defects were clarified. Research limitations/implications The results shows that the pores were the main defects present in the SLM-processed AlSi10Mg sample, which decreases the densification level of the sample. Practical implications The optimal processing parameters (argon pressure of 1,000 Pa, laser power of 180 W, scan speed of 1,000 mm/s, powder layer thickness of 35 µm and hatch spacing of 50 µm ) applied during laser melting can improve the quality of selective laser melting of AlSi10Mg, Social implications It can provide a technological support for 3D printing. Originality/value Based on the analysis of the pore and balling formation mechanisms, the optimal processing parameters have been obtained, which were argon pressure of 1,000 Pa, laser power of 180 W, scan speed of 1,000 mm/s, powder layer thickness of 35 µm and hatch spacing of 50 µm. Then, a near-fully dense sample free of any apparent pores on the cross-sectional microstructure was produced by SLM, wherein the relative density of the as-built samples is larger than 97.5%.

Effect of SLM Process Parameters on Relative Density of Maraging Steel (18Ni-300) Formed Parts

Effect of Process Parameters on Residual Stresses, Distortions, and Porosity in Selective Laser Melting of Maraging Steel 300

Relative Density of Mold Steel H13 Fabricated by Hybrid Laser Spot Melting

Effect of Processing Parameters on Forming Defects During Selective Laser Melting of AlSi10Mg Powder

Porosity, Hardness, Friction and Wear Performance Analysis of H13 SLM-Formed Samples

Experimental Research on Selective Laser Melting AlSi10Mg Alloys: Process, Densification and Performance

The effect of selective laser melting process parameters and remelting scanning strategy on relative density and surface hardness of stainless steel 316L

High-precision laser powder bed fusion of 18Ni300 maraging steel and its SiC reinforcement composite materials

Effect of Energy Density on the Mechanical Properties of 1.2709 Maraging Steel Produced by Laser Powder Bed Fusion

Influence of Processing Parameters and Heat Treatment on the Mechanical Properties of 18ni300 Manufactured by Laser Based Directed Energy Deposition

The Influences of Processing Parameters on Forming Characterizations During Laser Rapid Forming

Microstructure and Mechanical Properties of 18Ni-300 Maraging Steel Fabricated by Selective Laser Melting

Effects of powders and process parameters on density and hardness of A357 aluminum alloy fabricated by selective laser melting

Optimization of Selective Laser Melting Process for Maraging 300 Steel: Investigation the Impact of Parameters on Porosity, Microstructure, and Mechanical Properties

Effect of process parameter optimization on morphology and mechanical properties of Ti6Al4V alloy produced by selective laser melting

Influence of Layer Thickness and Heat Treatment on Microstructure and Properties of Selective Laser Melted Maraging Stainless Steel

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Process parameter optimization and mechanical properties for selective laser melting of AlSi10Mg alloy

Optimization of laser energy density and scanning strategy on the forming quality of 24CrNiMo low alloy steel manufactured by SLM

Maraging Steel Laser Additive Manufacturing Process and Microstructure Study

Coupling Analysis on Microstructure and Residual Stress in Selective Laser Melting (SLM) with Varying Key Process Parameters