Abstract:The accumulation of moisture inside the envelope under high-humid climates can strongly affect the hygrothermal properties and can lead to moisture-related damage / moulds to the materials, especially in severe weather con-ditions. However, the optimal insulation thickness of the exterior envelope is typically determined by factors such as overall heat transfer performance, carbon dioxide production and economic cost. The effect of insulation thickness on the annual average moisture content (AAMC) of a self-insulated exterior envelope is often neglected and seldom considered in the optimization process. In this study, a coupled heat, air and moisture transfer (HAM) model was derived and validated. Theoretical indices for water vapour transfer were implemented, such as moisture storage coefficient and moisture inertia factor. A simplified model for liquid water penetration and evaporation was also implemented. A novel four-dimensional moisture-energy-environment-economic (M3E) method that incorporates moisture content analysis was proposed for insulation thickness optimization. A case study was conducted on a self-insulated aerated concrete wall in two climate zones: the hot summer and cold winter (HSCW) zone and the cold zone. The insulation thickness interval investigated were 0-50 mm for interior thermal insulation (ITI) and 0-60 mm for exterior thermal insulation (ETI). The results of the case study showed that the AAMC of the entire envelope varied up to 15.2% (HSCW zone) and 10.0% (cold zone) for different insulation thicknesses. In the HSCW zone, the lowest AAMC of the outer part of the envelope adjacent to the atmosphere was found at 30 mm (ITI) or 20 mm (ETI), indicating the presence of turning thicknesses; while in the cold zones, the lowest AAMC was found at 50 mm (ITI) or 10 mm (ETI) with no turning thickness. The proposed theoretical implementations accounted for changes of AAMC in different interior/exterior insulation thicknesses and were verified with the results of numerical calculation. The proposed theoretical indices revealed an opposite effect of water vapour transfer and liquid water transfer on the AAMC for different insulation thicknesses, which can explain the presence of turning thickness. Furthermore, the selected optimal insulation thicknesses from Pareto fronts were found around 25-29 mm for ITI and 36-38 mm for ETI in two climate zones. The results from the M3E method showed a reduction in moisture risks (up to 62.91%) and mould growth risks (up to 4.84%) in the case study, successfully meeting the acceptable range of moisture risk and mould growth risk. The findings of this paper can help generate a new understanding of moisture transfer, and the proposed M3E method can be applied in all cases to reduce the moisture/mould growth risks in the design stage.

Numerical Analysis of the Dynamic Heat and Moisture Coupling Transfer Within Typical Building Walls in Severe Cold Region of China

Numerical Study On Energy Consumption Characteristics For Wall Insulation Structure In Hot Summer And Cold Winter Zone

Numerical Study on Wall Insulation Construction Affecting the Energy Consumption under the Intermittent and Loculose Energy Use

Optimum Insulation Thickness of External Walls by Integrating Indoor Moisture Buffering Effect: a Case Study in the Hot-Summer-cold-winter Zone of China

The Moisture Distribution in Wall-to-floor Thermal Bridges and Its Influence on Mould Growth

Heat and Moisture Transfer in Wall-to-floor Thermal Bridges and Its Influence on Thermal Performance

The Energy Saving Effect of Different Wall Insulation Configurations with the Intermittent and Compartmental Heating Method

Hygrothermal Performance of a Self-Insulated Exterior Wall with Various Exterior/interior Insulation Thicknesses in Two Climate Zones in China: A Novel Moisture-Energy-environment-economic (M3E) Method in Insulation Thickness Optimization

Energy Efficiency For Airtightness And Exterior Wall Insulation Of Passive Houses In Hot Summer And Cold Winter Zone Of China

Moisture proof calculation of envelope in severe cold zone

Moisture Distribution in Wall-to-floor Thermal Bridges under the Analysis of Coupled Heat and Moisture Transfer

Numerical Simulation Study on the Hygrothermal Performance of Building Exterior Walls under Dynamic Wind-Driven Rain Condition

Sensitivity Analysis of Traditional Solid Masonry Wall to Frost Damage in North China

Numerical investigations of dynamic moisture response to the climates inside wooden components in timber buildings and its potential threats

Thermal and moisture performance of external thermal insulation system with periodic freezing-thawing

Numerical simulation of the freezing process of concrete

Facilitator of moisture accumulation in building envelopes and its influences on condensation and mould growth

Numerical Analysis of the Dynamic Heat Transfer Through an External Wall under Different Outside Temperatures

Moisture transport analysis for integrated structures of flat plate solar collector and building envelope

Study on heat transfer of light steel-framed composite walls in cold area

SIMULATION AND EVALUATION ON THE THERMAL PERFORMANCE OF PCM WALLBOARD ROOMS LOCATED IN VARIOUS CLIMATE REGIONS OF CHINA IN SUMMER