Abstract:The C=C double bonds in the main chain of hydroxyl-terminated polybutadiene (DHTPB), obtained by the degradation of polybutadiene rubber, were partially epoxided using m-chloroperoxybenzoic acid (mCPBA) as epoxidation reagent. A series of epoxided HTPBs (EHTPB) with different epoxy contents (5%, 10% and 15%) were prepared by tuning the molar ratio of mCPBA to C=C double bonds. The structures of EHTPBs were characterized by Fourier transform-infrared (FTIR), nuclear magnetic resonance (H-1-NMR) spectroscopy and gel permeation chromatography (GPC). The epoxy percent in EHTPBs from H-1-NMR spectra was in accordance with the design. In addition, a series of EHTPB-based polyurethane elastomers (EPU) were prepared by the reaction between EHTPB and 4,4'-diphenylmethane diisocyanate with 1,4-butanediol as a chain extender. Mechanical and thermal properties of the EPU samples were characterized by tensile test, differential scanning calorimetry (DSC) and thermal gravity analysis (TGA). With increased epoxy percent in EHTPB, the Young's modulus and the tensile strength of the EPU samples increased, whereas the elongation at break decreased. The sample EPU10 prepared with 10% of epoxy had the best mechanical properties with 8.82 MPa as Young's modulus, 7.83 MPa as tensile strength, and (485 +/- 23)% as elongation at break. The elasticity recovery of the EPU sample was slightly better than HTPB-based PU (EPU0). The results with TGA test showed that the thermal degradation of EPU, similar to EPU0, was divided into three stages. However, the EPU samples had better thermal stability with the initial degradation temperature at 210 degrees C, about 30 degrees C higher than that of EPU0. The DSC results showed that the glass transition temperature (T-g) of EPU gradually increased as epoxy percent was increased, though still lower than that of HTPB (FHTPB) based PUs prepared by free-radical polymerization.

Mechanical and Underwater Acoustic Properties of the Polyurethane Elastomers with Different Hard Segment Contents

Preparation and Properties of Epoxided Hydroxyl-terminated Polybutadiene Based Polyurethane Elastomers

Effect of soft segment structure on properties of polyurethane elastomers

Synthesis of High-Toughness Waterborne Polyurethane Utilizing Self-Emulsifying CO2-based Polyols

Synthesis and properties of elastomeric polyurethane for grouting

The Structure and Dynamic Properties of Thermoplastic Polyurethane Elastomer/Hindered Phenol Hybrids

Preparation and Characterization of Silicone Oil Modified Polyurethane Damping Materials

Synthesis and Properties of Cast PU Elastomers with Molecularly Uniform Hard Segments Based on TDI and DMTDA

Studies on the influence of soft-segment structure on the properties of polyurethane adhesive

Design and Performance of Polyurethane Elastomers Composed with Different Soft Segments

Mechanical Properties of Polyurethane Foams Prepared from Liquefied Corn Stover with PAPI.

Thermal stimuli response diphenylmethane diisocyanate‐based polyurethane elastomer via adjustable silicon‐induced distinctive microstructure

Influence of the hard segments content on the structure, viscoelastic and adhesion properties of thermoplastic polyurethane pressure sensitive adhesives

Synthesis and Application of Hydroxyethyl Methacrylate Modified Waterborne Polyurethane

Effects of Soft-Segments on the Structure and Properties of Polyurethane Emulsion

Synthesis and properties of waterborne polyurethane-based PTMG and PDMS as soft segment

Preparation and characterization of silicone oligomer modified polyurethane acrylates for leather finishing

Effect of Water Content on the Aggregation and Adhesion Properties of Waterborne Polyurethane

The Effects of MDI Isomer on the Micro-Structure and Property of Polyurethane Elastomer

Investigating the structure and properties of polyurethane hydrogels with varying soft and hard segments

Effects of Soft Segment and Degree of Crosslinking on HTPB Polyurethane Urea Compressional Property