Abstract:As China's aluminum electrolysis industry expanded its production capacity, it produced a large amount of bath materials– cryolite based molten salt, which is not utilized fast enough and piled up in aluminum factories. It is of great significance to find a proper way to process the accumulated bath materials. Through the method introduced in this paper, aluminum fluoride can be produced from cryolite-based electrolyte and fed back into the aluminum electrolysis cell as a necessary additive. This method includes four steps: Calcination of crystalline aluminum nitrate with cryolite. Cryolite and crystalline aluminum nitrate are mixed and preheated. The main chemical reaction that occurs in this step will produce sodium nitrate (NaNO3), β-aluminum fluoride (β-AlF3), chiolite (Na5Al3F14) and the aluminum hydroxyfluoride hydrate (AHF). After calcination, the products are washed with water to separate soluble NaNO3 from the other products. The insoluble products obtained after washing are calcined with ammonium bifluoride to convert AHF into AlF3. The mixture obtained after preheating is then washed with an aqueous solution of aluminum salt (such as Al(NO3)3) to remove Na5Al3F14. Aluminum fluoride of high purity is obtained in the end. Calcination step is the most important among the four steps. The effects of calcination temperature (85 – 135 ℃) and molar ratio of crystalline aluminum nitrate to cryolite (0.5 – 2) on the conversion rate of cryolite were studied. The experimental results show that the highest conversion rate of cryolite can reach 97.03%. Through SEM, EDS, ICP and other analysis methods, it was found the final products contained more than 98.8 wt% aluminum fluoride and less than 0.4 wt% sodium, and the average particle size of aluminum fluoride is approximately 15 – 20 µm.

Development and Application of New Dry Barrier Powder Refractory for Aluminum Electrolysis Cell

The development of 85kA three-layer electrolysis cell for refining of aluminium

Technology Research on Decreasing the Aluminum Surface Waves and Reducing the Cathode Voltage Drop in Aluminum Electrolysis Cell

Technical Study for Fabrication of New Cermet Used As Inert Anode in Aluminum Molten-Salt Electrolysis

Pilot experiments of low temperature (700 ~ 800°C) aluminum electrolysis in A 5KA Caluminum reduction cell

Optimization of an Artificial Solid Electrolyte Interphase Formed on an Aluminum Anode and Its Application in Rechargeable Aqueous Aluminum Batteries

Application of Full Heat Insulation Lining in 300 Ka Aluminum Electrolysis Cells

Recycling of spent refractory materials to produce Al–Si master alloys via the aluminum reduction cell

Study on preparation of aluminum fluoride from cryolite

Improved CFD Modeling of the Whole-Cell Side Ledge Behavior in Aluminum Electrolysis Cell

PILOT EXPERIMENTS OF LOW TEMPERATURE (700 similar to 800 degrees C) ALUMINUM ELECTROLYSIS IN A 5KA ALUMINUM REDUCTION CELL

3D Freeze shape study of the aluminum electrolysis cells using finite element method

Modeling and Parametric Study of Spent Refractory Material Dissolution in an Aluminum Reduction Cell

Stepwise extraction of lithium and potassium and recovery of fluoride from aluminum electrolyte wastes through calcification roasting-two-stage leaching

Study on Preparation of Cryolite by Chemical Precipitation of Fluorine from Aluminum Electrolytic Industrial Wastewater

Advances in Research on Electrical Conductivity of Aluminum Electrolyte Melts

Development and application of integrated technology of current-intensifying and high-efficiency energy-saving for aluminium reduction

Efficient Extraction and Recovery of Lithium from Waste Aluminum Cryolite Electrolyte

Preparation of aluminum fluoride from carbon residue in aluminum electrolysis cell by roasting-leaching method

Effective Chloride Ion Resistance of Aluminum Powder Through Interface Electric Field Designing

Experimental Aluminum Reduction Cell with Suspended Cathode and Finite Element Analysis of Its Current Field