Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. This paper investigates the correlation between the surface quality and the cross-sectional quality, microstructure, internal defects, and mechanical properties of specimens formed by selective laser melting (SLM) under different scanning speeds and scanning intervals. Therefore, different machining parameters were chosen to prepare titanium alloy specimens by SLM technique. The surface morphology of the specimens was characterized using a light microscope, and the surface quality, microstructure, internal defects, and deep connection of the mechanical properties of the specimens formed under different parameters were investigated. In addition, numerical simulation of the melt pool morphology under different scanning speeds was used. The results show that there is a strong correlation between the surface quality of the specimen and the section quality and mechanical properties. When the scanning speed is 350 mm/s, the surface roughness is 14.7 μm, the density is 99.99%, the tensile strength and yield strength are 1209 and 1151 Mpa respectively, and the surface quality, cross-sectional quality and mechanical properties all tend to deteriorate as the scanning speed increases. When the scanning interval is 0.11 mm, the mechanical properties of surface quality and cross-sectional quality are optimal, the surface roughness is 14.5 μm, and the density reaches 99.99%, at this time, the microscopic needle martensite α′ phase is uniformly distributed and refined, and its mechanical properties are optimal, the tensile strength is 1239 MPa, and the internal hole defects are less. Numerical simulations of a single track melt pool show that the depth of depression caused by the recoil pressure is larger and the melt pool is deeper when the scanning speed is 350 mm/s. Therefore, it has better fluidity and ductility. Simulation results of the double tracks show that when the scanning interval is 130 μm, a large amount of incompletely melted powder at the midline of the double track does not lap well, which leads to the formation of pore defects inside the specimen. The above simulation results are highly consistent with the surface quality of the specimens during the experiments, which provides a guide to analyze the connection between the melt pool evolution and the Ti6Al4V molding quality.

Effects of Defects and Microstructures on Tensile Properties of Selective Laser Melted Ti6Al4V Alloys Fabricated in the Optimal Process Zone

Experimental Characterization and Strengthening Mechanism of Process-Structure-property of Selective Laser Melted 316 L

Study of pore defect and mechanical properties in selective laser melted Ti6Al4V alloy based on X-ray computed tomography

Tensile Behavior of Ti-6Al-4V Alloy Fabricated by Selective Laser Melting: Effects of Microstructures and As-Built Surface Quality

Experimental Characterization and Yield Strength Model for Process-Structure-Property of Selective Laser Melted 316L

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Study on the Tensile and Shear Behaviors of Selective Laser Melting Manufactured Ti6Al4V

The relationship between the macro- and microstructure and the mechanical properties of selective-laser-melted Ti6Al4V samples under low energy inputs: Simulation and experiment

Microstructure and mechanical deformation behavior of selective laser melted Ti6Al4V ELI alloy porous structures

Effect of Overlapping Remelting on Microstructures and Mechanical Properties of Selective Laser‐Melted Ti‐6Al‐4V Alloy

Comparison of the microstructures and mechanical properties of Ti–6Al–4V fabricated by selective laser melting and electron beam melting

Microstructure, Mechanical Properties, and Constitutive Models for Ti–6Al–4V Alloy Fabricated by Selective Laser Melting (SLM)

Investigation of the scanning strategy on the microstructure and tensile property of Ti6Al4V alloy fabricated by selective laser melting

Role of processing parameters on relative density, microstructure and mechanical properties of selective laser melted titanium alloy

Effect of energy density on quasi-static and dynamic mechanical properties of Ti–6Al–4V alloy additive-manufactured by selective laser melting

Selective laser melting processing of heterostructured Ti6Al4V/FeCoNiCrMo alloy with superior strength and ductility

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

X-ray CT analysis of the influence of process on defect in Ti-6Al-4V parts produced with Selective Laser Melting technology

Influence of Manufacturing Geometric Defects on the Mechanical Properties of AlSi10Mg Alloy Fabricated by Selective Laser Melting

Study on the mechanism of correlation between surface quality and tissue properties of Ti6Al4V alloy formed by selective laser melting