Abstract:Many factors can affect the formability of TC4 alloy in laser additive, and the effects of their interaction are complex. The essence lies in the energy input of the molten pool. In this study, the energy input of the molten pool was characterized by the laser volume energy density under the coupling of multiple process parameters. The effects of volume energy density on the microstructure evolution and mechanical properties of TC4 alloy were studied, and the fracture mechanism was discussed. The results showed that the microstructure of TC4 alloy prepared by selective laser melting (SLM) was composed of α phase, metastable α′ phase, and a small amount of equiaxed nano-β phase. When the TC4 powder was irradiated by low volume energy density, fine columnar β grain with low texture intensity and random grain orientation distribution appear. Meanwhile, a large number of fine acicular martensite α′ phases generated inside the β grains, but fewer nano-β phases precipitated. At the same volume energy density, compared with increasing laser power, reducing the scanning speed could lead to the coarsening of α′ martensite, and more nano-β phase precipitated at the martensite boundary. The volume energy density greatly influenced the elongation (EL) but had little effect on the ultimate tensile strength (UTS), and the UTS could reach up to 1507 MPa. The decreasing volume energy density was beneficial to improve the plasticity, mainly attributed to the increasing deformation coordination ability caused by the refinement of α/α′ martensite and the reduction of the nano-β phase. When the volume energy density was 36 J/mm 3 , the fine columnar β grain precipitated, and a ductile fracture displayed with high-density dimples shown in fracture morphology. The mapping relationship between process, microstructure and properties was established, which provided a theoretical basis for process, microstructure optimization and performance improvement.

Effect of energy density on quasi-static and dynamic mechanical properties of Ti–6Al–4V alloy additive-manufactured by selective laser melting

Effect of Heat Treatment on Microstructure and Mechanical Properties of Ti6Al4V Alloy Fabricated by Selective Laser Melting

Tensile Behavior of Ti-6Al-4V Alloy Fabricated by Selective Laser Melting: Effects of Microstructures and As-Built Surface Quality

Microstructure and Mechanical Properties of As-Built Ti-6Al-4V and Ti-6Al-7Nb Alloys Produced by Selective Laser Melting Technology

Effect of Overlapping Remelting on Microstructures and Mechanical Properties of Selective Laser‐Melted Ti‐6Al‐4V Alloy

Achieving Equiaxed Transition and Excellent Mechanical Properties in a Novel Near-β Titanium Alloy by Regulating the Volume Energy Density of Selective Laser Melting

Selective laser melting processing of heterostructured Ti6Al4V/FeCoNiCrMo alloy with superior strength and ductility

Mechanical Behavior of Additive Manufacturing (AM) and Wrought Ti6Al4V with a Martensitic Microstructure

Processing Parameter Effects on Residual Stress and Mechanical Properties of Selective Laser Melted Ti6Al4V

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Microstructural Characteristics and Material Failure Mechanism of SLM Ti-6Al-4V-Zn Alloy

Fatigue Crack Initiation and Growth Behaviors of Additively Manufactured Ti-6AI-4V Alloy After Hot Isostatic Pressing Post-Process

Role of processing parameters on relative density, microstructure and mechanical properties of selective laser melted titanium alloy

Selective Laser Melting of Ti6Al4V: Effects of Heat Accumulation Phenomena due to Building Orientation

Effect of Hot Isostatic Pressing and Solution Heat Treatment on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Manufactured by Selective Laser Melting

Microstructure and Mechanical Properties of Ti-6Al-4V Manufactured by Selective Laser Melting after Stress Relieving, Hot Isostatic Pressing Treatment, and Post-Heat Treatment

Effect of volume energy density on microstructure and mechanical properties of TC4 alloy by selective laser melting

Effects of heat treatment and hot isostatic pressing on microstructure and fatigue improvements in Ti-6Al-4V alloy fabricated by selective laser melting

Microstructure, Mechanical Properties, and Constitutive Models for Ti–6Al–4V Alloy Fabricated by Selective Laser Melting (SLM)

The Low-Cycle Fatigue Behavior, Failure Mechanism and Prediction of SLM Ti-6Al-4V Alloy with Different Heat Treatment Methods

The effect of process parameters on the physical and mechanical properties of Ti fabricated by selective laser melting using ball milled powders