Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. This paper investigates the correlation between the surface quality and the cross-sectional quality, microstructure, internal defects, and mechanical properties of specimens formed by selective laser melting (SLM) under different scanning speeds and scanning intervals. Therefore, different machining parameters were chosen to prepare titanium alloy specimens by SLM technique. The surface morphology of the specimens was characterized using a light microscope, and the surface quality, microstructure, internal defects, and deep connection of the mechanical properties of the specimens formed under different parameters were investigated. In addition, numerical simulation of the melt pool morphology under different scanning speeds was used. The results show that there is a strong correlation between the surface quality of the specimen and the section quality and mechanical properties. When the scanning speed is 350 mm/s, the surface roughness is 14.7 μm, the density is 99.99%, the tensile strength and yield strength are 1209 and 1151 Mpa respectively, and the surface quality, cross-sectional quality and mechanical properties all tend to deteriorate as the scanning speed increases. When the scanning interval is 0.11 mm, the mechanical properties of surface quality and cross-sectional quality are optimal, the surface roughness is 14.5 μm, and the density reaches 99.99%, at this time, the microscopic needle martensite α′ phase is uniformly distributed and refined, and its mechanical properties are optimal, the tensile strength is 1239 MPa, and the internal hole defects are less. Numerical simulations of a single track melt pool show that the depth of depression caused by the recoil pressure is larger and the melt pool is deeper when the scanning speed is 350 mm/s. Therefore, it has better fluidity and ductility. Simulation results of the double tracks show that when the scanning interval is 130 μm, a large amount of incompletely melted powder at the midline of the double track does not lap well, which leads to the formation of pore defects inside the specimen. The above simulation results are highly consistent with the surface quality of the specimens during the experiments, which provides a guide to analyze the connection between the melt pool evolution and the Ti6Al4V molding quality.

X-ray CT analysis of the influence of process on defect in Ti-6Al-4V parts produced with Selective Laser Melting technology

Study of pore defect and mechanical properties in selective laser melted Ti6Al4V alloy based on X-ray computed tomography

Investigation of the Effect of Artificial Internal Defects on the Tensile Behavior of Laser Powder Bed Fusion 17–4 Stainless Steel Samples: Simultaneous Tensile Testing and X-Ray Computed Tomography

Process parameter optimization for selective laser melting Ti-6Al-4V with high layer thickness

Quantitative study of geometric characteristics and formation mechanism of porosity defects in selective laser melted Ti6Al4V alloy by micro-computed tomography

Study on the mechanism of correlation between surface quality and tissue properties of Ti6Al4V alloy formed by selective laser melting

The relationship between the macro- and microstructure and the mechanical properties of selective-laser-melted Ti6Al4V samples under low energy inputs: Simulation and experiment

Coupling Analysis on Microstructure and Residual Stress in Selective Laser Melting (SLM) with Varying Key Process Parameters

Study of residual stress in selective laser melting of Ti6Al4V

Use of X-ray Computed Tomography for Assessing Defects in Ti Grade 5 Parts Produced by Laser Melting Deposition

Effect of Process Parameters and Layer Thickness on the Quality and Performance of Ti-6Al-4V Fabricated by Selective Laser Melting

Uncertainties Induced by Processing Parameter Variation in Selective Laser Melting of Ti6Al4V Revealed by In-Situ X-ray Imaging

Processing Parameter Effects on Residual Stress and Mechanical Properties of Selective Laser Melted Ti6Al4V

Study on the Tensile and Shear Behaviors of Selective Laser Melting Manufactured Ti6Al4V

Main Defects Observed in Titanium GRADE II and 316L Stainless Steel Elements Obtained by Selective Laser Melting

Effect of Process Parameters on the Microstructure and Properties of Cu–Cr–Nb–Ti Alloy Manufactured by Selective Laser Melting

In-situ Monitoring and Defect Detection of Selective Laser Melting Process and Impact of Process Parameters on the Quality of Fabricated SS 316L

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

The effect of process parameters on the physical and mechanical properties of Ti fabricated by selective laser melting using ball milled powders

The Low-Cycle Fatigue Behavior, Failure Mechanism and Prediction of SLM Ti-6Al-4V Alloy with Different Heat Treatment Methods

Study on the effects of the processing parameters on the single tracks and the block support structures fabricated by selective laser melting