Miniature All-Fiber Fabry-Perot Interferometer

Xinpu Zhang,Baoyun Wu

DOI: https://doi.org/10.1364/ofs.2020.w4.85

2021-01-01

Abstract:We propose and experimentally demonstrate a novel miniature all-fiber Fabry-Perot (FP) interferometer. This FP interferometer is formed by an angled fiber, which is made by a simple end-face polishing process.

What problem does this paper attempt to address?

Angled Fiber-Based Fabry–Perot Interferometer

Xinpu Zhang,Lixia Li,Xihua Zou,Bin Luo,Wei Pan,Lianshan Yan,Qiang Wu

DOI: https://doi.org/10.1364/ol.45.000292

IF: 3.6

2020-01-01

Optics Letters

Abstract:Herein, we propose and experimentally demonstrate a novel, to the best of our knowledge, all-fiber Fabry–Perot (FP) interferometer that is formed by a simple angled fiber that can function as a beam splitter. According to the principle of the angled fiber, we verify the influence of an oblique angle on the light propagation path and light intensity ratio. Subsequently, angled fiber-based FP interferometers are experimentally demonstrated, and the influence of the oblique angle on the visibility of interference fringes and temperature characteristics is investigated. Finally, the temperature characteristics of this proposed FP interferometer are investigated experimentally, and the temperature sensitivity is 12.62 and 10.89 pm/°C for 42° and 40° angled fiber-based fiber FP interferometers, respectively. This proposed FP interferometer is fabricated by using a simple angled fiber, which has the advantages of ease of fabrication and all-fiber characteristics and hence can meet the requirements of mass production and high stability in various practical application areas.
All-Fiber Fabry-Perot Resonators Based on Microfiber Sagnac Loop Mirrors

Shan-Shan Wang,Zhi-Fang Hu,Yu-Hang Li,Li-Min Tong

DOI: https://doi.org/10.1364/ol.34.000253

IF: 3.6

2009-01-01

Optics Letters

Abstract:We demonstrate all fiber Fabry-Perot resonators (F-P resonators) based on Sagnac loop mirrors assembled with tellurite microfibers. As-assembled F-P resonators, with dimensions of hundreds of micrometers, show clear resonant responses with typical quality factor of about 5700, free spectral range of about 1 nm, and a maximum extinction ratio of 18 dB. The reflectivity of the loop mirror and the effective cavity length of the F-P resonator can be tuned by micromanipulation under an optical microscope. F-P resonators demonstrated here show advantages of small size, good resonance, easy fabrication, tunability, and easy integration with fiber systems. (C) 2009 Optical Society of America
Angled Fiber-Based FP Interferometer

Baoyun Wu,Xinpu Zhang,Lianshan Yan,Xihua Zou,Bin Luo,Wei Pan

2019-01-01

Abstract:A end-face splitter-based fiber Fabry-Perot (FP) interferometer is proposed. The feasibility of this FP interferometer is experimentally verified. And the influence of the splitter's angle on the visibility of the spectrum is investigated.
Miniaturized Fiber Inline Fabry-Perot Interferometer Fabricated with A Femtosecond Laser

Tao Wei,Yukun Han,Hai-Lung Tsai,Hai Xiao

DOI: https://doi.org/10.1364/ol.33.000536

2008-01-01

Abstract:We report a miniaturized inline Fabry-Perot interferometer directly fabricated on a single-mode optical fiber with a femtosecond laser. The device had a loss of 16 dB and an interference visibility exceeding 14 dB. The device was tested and survived in high temperatures up to 1100 degrees C. With an accessible cavity and all-glass structure, the new device is attractive for sensing applications in high-temperature harsh environments.
Chirped Fiber Tip Fabry-Perot Interferometer.

Xinpu Zhang,Liyang Shao,Xihua Zou,Bin Luo,Wei Pan,Lianshan Yan

DOI: https://doi.org/10.1364/ol.42.003474

IF: 3.6

2017-01-01

Optics Letters

Abstract:We demonstrate a novel fiber tip Fabry-Perot (FP) interferometer with a chirped spectral characteristic. The FP interferometer is formed by an etched chirped fiber Bragg grating (FBG) and the fiber tip broadband end-face mirror, and the etched chirped FBG is prepared by a dynamic chemical etching process, shaping the taper and reducing the size from 125 μm to just a few micrometers. Due to the spectral characteristic of the etched chirped FBG, the different resonance wavelengths correspond to different gating positions which give rise to the gradient cavity length in the chirped fiber tip FP interferometer; thus, this FP interferometer possesses a chirped interference spectrum. Subsequently, the FP interferometer is fabricated, and the temperature response is investigated by measuring the wavelength shift of the resonance dips in the reflection spectrum. Significantly, because of its special interference principle and configuration, we experimentally demonstrate that this FP interferometer can be used for the spatial localization of the external temperature perturbations.
In-line All-Fiber Fabry-Perot and Mach-Zehnder Interferometers Formed by Hollow Fiber with Lateral Offset

Yun Jiang Rao,De Wen Duan,Lai Cai Xu,Ming Deng,Tao Zhu

DOI: https://doi.org/10.1117/12.884846

2011-01-01

Abstract:Two kinds of novel in-line all-fiber interferometers, including tip Farby-Perot interferometer and compact Mach-Zehnder interferometer, are proposed and demonstrated by automatically fusion splicing a short section of hollow fiber to the end of a single-mode fiber (SMF) and sandwiching a section of hollow fiber in two section of SMF with a tiny intentional lateral offset that induces the optical path difference (OPD) required to form the two interferometers, respectively. Temperature responses of both the two interferometers are studied experimentally. It is anticipated that such an easy making, compact and low cost fiber-optic interferometers could find important applications in practice.
In-Fiber Fabry–Perot and Mach–Zehnder Interferometers Based on Hollow Optical Fiber Fabricated by Arc Fusion Splicing with Small Lateral Offsets

De-Wen Duan,Yun-Jiang Rao,Lai-Cai Xu,Tao Zhu,Ming Deng,Di Wu,Jun Yao

DOI: https://doi.org/10.1016/j.optcom.2011.07.052

IF: 2.4

2011-01-01

Optics Communications

Abstract:Two kinds of in-line all-fiber interferometers, including tip Fabry–Perot interferometer and compact Mach–Zehnder interferometer, are proposed and demonstrated by fusion splicing a short section of hollow optical fiber (HOF) to the end of single-mode fiber (SMF) and sandwiching a section of HOF in between two sections of SMF, respectively. In both interferometers, a small lateral offset is introduced to induce the optical path difference required to form the interferometer. Temperature responses of both types of interferometers are studied experimentally. It is anticipated that such easy making, compact and low-cost fiber-optic interferometers could find important applications in practice.
Ultra-small Fiber Taper Fabry-Perot Modal Interferometer

Jun-long Kou,Jing Feng,Fei Xu,Yan-qing Lu

DOI: https://doi.org/10.1049/cp.2010.1242

2010-01-01

Abstract:We present an ultra-small fiber taper based Fabry-Perot modal interferometer (FPMI). Our FPMI is made of a microcavity (~ 4.4 μm in length) directly fabricated into a fiber taper with its diameter less than 10 μm. Its working head is a miniaturized single-mode-multi-mode fiber configuration without splicing. The underlying mechanism of FPMI is the interference among reflected fundamental mode and excited high-order modes at the end-faces. This kind of interferometer takes up little space because of its unique geometry and ultra-small size. The new device is attractive for sensing applications such as in high-temperature harsh environments with the advantages of fast response and high sensitivity.
Novel miniaturized fabry-perot refractometer based on a simplified hollow-core fiber with a hollow silica sphere tip

Dora Juan Juan Hu,Yixin Wang,Junlong Lim,Taishi Zhang,Karolina Barbara Mileńko,Zhihao Chen,Meng Jiang,Guanghui Wang,Feng Luan,Ping Shum,Qizhen Sun,Huifeng Wei,Weijun Tong,Tomasz R. Woliński

DOI: https://doi.org/10.1109/JSEN.2011.2167678

IF: 4.3

2012-01-01

IEEE Sensors Journal

Abstract:In this paper, we report and demonstrate a novel miniaturized intrinsic Fabry-Perot interferometer (IFPI) based on a simplified hollow core fiber ended with a hollow silica sphere tip. The hollow core fiber is spliced to single mode fiber and subsequently applied with fusion arc at the end, forming a hollow sphere with a thin silica wall. The reflection spectrum is modulated by the environment of ...
Miniature Fabry-Perot Interferometer Based on a Movable Microsphere Reflector.

Ke Tian,Jibo Yu,Xin Wang,Haiyan Zhao,Dejun Liu,Elfed Lewis,Gerald Farrell,Pen Wang

DOI: https://doi.org/10.1364/ol.385222

2020-01-01

Abstract:We propose and demonstrate a miniature Fabry-Perot interferometer (FPI) based on a movable microsphere reflector. The movable microsphere acts as a good reflector, with the reflections occurring at the spliced single-mode fiber/hollow-core fiber interface and the surface of a microsphere, resulting in two-beam interference. The silica microsphere is formed at the tip of a half-tapered optical fiber, and its diameter can be reduced to miniaturize the FPI. The movable microsphere interferometer exhibits a highly linear response to external displacement change, and a high displacement sensitivity of 11.9 pm/nm with a nanoscale resolution of 1.7 nm is achieved. Wide-range displacement can also be measured by monitoring the changes in the free spectral range of the reflection spectrum. Therefore, this miniaturized FPI may find use in applications in nano-displacement measurement fields, and the concept of a movable microsphere reflector is of great significance for the miniaturization of micro-photonic devices.
Fiber Fabry-Perot Interferometer with Controllable Temperature Sensitivity

Xinpu Zhang,Wei Peng,Yang Zhang

DOI: https://doi.org/10.1364/ol.40.005658

IF: 3.6

2015-01-01

Optics Letters

Abstract:We proposed a fiber taper based on the Fabry-Perot (FP) interferometer structure with controllable temperature sensitivity. The FP interferometer is formed by inserting a segment of tapered fiber tip into the capillary and subsequently splicing the other end of the capillary to a single-mode fiber (SMF), the tapered fiber endface, and the spliced face form the FP cavity. Through controlling the inserted tapered fiber length, a series of FP interferometers were made. Because the inserted taper tip has the degree of freedom along the fiber axial, when the FP interferometer is subjected to temperature variation, the thermal expansion of the fiber taper tip will resist the FP cavity length change caused by the evolution of capillary length, and we can control the temperature sensitivity by adjusting the inserted taper length. In this structure, the equivalent thermal expansion coefficient of the FP interferometer can be defined; it was used to evaluate the temperature sensitivity of the FP interferometer, which provides an effective method to eliminate the temperature effect and to enhance other measurement accuracy. We fabricated the FP interferometers and calibrated their temperature characters by measuring the wavelength shift of the resonance dips in the reflection spectrum. In a temperature range of 50 degrees C to 150 degrees C, the corresponding temperature sensitivities can be controlled between 0 and 1.97 pm/degrees C when the inserted taper is between 75 and 160 mu m. Because of its controllable temperature sensitivity, ease of fabrication, and low cost, this FP interferometer can meet different temperature sensitivity requirements in various application areas, especially in the fields which need temperature insensitivity. (C) 2015 Optical Society of America
High-temperature resistant, all-fiber miniature interferometer

Xinpu Zhang,Xuhui Zhang,Yang Zhang,Wei Peng

DOI: https://doi.org/10.1016/j.ijleo.2022.168711

IF: 3.1

2022-04-01

Optik

Abstract:Herein, a novel high-temperature resistant, miniature all-fiber interferometer is experimentally demonstrated. This interferometer can be formed by an angled fiber without any additional components, which is fabricated by a simple one-step fiber polishing, thus, this angled-fiber based miniature interferometer can serve as a direct sensing probe. The qualitative relationship between fiber interferometer’s visibility and fiber angle is calculated by using the coupled mode theory, and this interferometer is experimentally demonstrated, and then, the temperature response and high-temperature resistance of a 39° angled-fiber based interferometer is investigated. The experimental results show that the sensitivity of this 39° angled-fiber interferometer is 13.7 pm/°C in the range of 500–1000 °C. Besides, the high-temperature resistance reveals that this all-fiber interferometer excellent high-temperature survivability while the temperature is up to 1000 °C.

optics
Miniature Fabry-Perot interferometric sensor for temperature measurement based on photonic crystal fiber

Xing-hu Fu,Hai-yang Xie,Feng Wang,Peng Jiang,Guang-wei Fu,Wei-hong Bi

DOI: https://doi.org/10.1007/s11801-015-5131-x

2015-09-01

Optoelectronics Letters

Abstract:A novel miniature Fabry-Perot interferometric (FPI) temperature sensor is proposed and demonstrated experimentally. The modal interferometer is fabricated by just splicing a section of photonic crystal fiber (PCF) with a single-mode fiber (SMF). The air holes of the PCF are fully collapsed by the discharge arc during the splicing procedure to enhance the reflection coefficient of the splicing point. The transmission spectra with different temperatures are measured, and the experimental results show that the linear response of 11.12 pm/°C in the range of 30–80 °C is obtained. This sensor has potential applications in temperature measurement field.

optics
All-fiber Miniature Fabry-Perot Interferometer As High Temperature Sensor

柯涛,朱涛,饶云江,徐敏,段德稳

DOI: https://doi.org/10.3969/j.issn.1007-2276.2010.01.022

2010-01-01

Infrared and Laser Engineering

Abstract:All-fiber miniature Fabry-Perot(F-P) interferometer was fabricated by splicing one section of special photonic crystal fiber(MM-HNA-5) to a single-mode fiber SMF28e with an axis offset.The optical principle and mechanism of the miniature F-P interferometer was analyzed.The MM-HNA-5 fiber had much larger thermo-optical coefficient,thus could be used for temperature measurement.Experimental results show that the temperature measurement range of the proposed sensor is larger than that of the conventional ones,and it is up to 1 200 ℃ .In particular,when the length of the F-P cavity was about 3.46 mm,the temperature sensitivity of the optical path difference was 103 nm/℃,and the linearity of temperature measurement was 0.995 7.This kind of F-P temperature sensor will have potential applications to national defense and civil industry due to its stable structure,small size,high sensitivity and large measurement range.
Intrinsic Fiber-Optic Fabry-Perot Interferometer Based On Arc Discharge And Single-Mode Fiber

Di Wu,Tao Zhu,Guo-Yin Wang,Jian-Yu Fu,Xiao-Guang Lin,Guang-Lei Gou

DOI: https://doi.org/10.1364/AO.52.002670

IF: 1.9

2013-01-01

Applied Optics

Abstract:We propose a simple intrinsic Fabry-Perot interferometer (FPI) based on single-mode fiber, where a thin film is formed by arc discharge to serve as one mirror of the FPI cavity. The temperature and refractive-index (RI) characteristics of the proposed device are investigated. Experimental results show that the device can provide temperature-independent measurement of RI with a fringe-contrast sensitivity of similar to 72.59 dB/RIU (RI units). Meanwhile, it can also be used as a temperature sensor with a wavelength sensitivity of similar to 8 pm/degrees C. Therefore, the potential simultaneous measurement of RI and temperature could be realized by detecting the variations of fringe contrast and wavelength, respectively. (C) 2013 Optical Society of America
Miniature Fourier Transform Spectrometer Based on a Fiber-Tip Interferometer.

Chunyang Han,Hui Ding,Baojin Li,Lei Shi,Haodong Xu

DOI: https://doi.org/10.1364/oe.456320

IF: 3.8

2022-01-01

Optics Express

Abstract:The miniaturization of spectrometers have attracted much attention owning to the demand for portable or in situ spectral analysis in a wide variety of fields, but it is a great challenge to push them into practical applications due to high cost, complicated configuration, and sensitivity to external disturbance. We report on a miniature Fourier transform (FT) spectrometer based on fiber-tip Fizeau interferometer. Hand pulling or any other types of force can be used to drive optical path difference (OPD) scan. Interferences are monitored as a function of time by two photodetectors, one is used to detect the whole interferogram while the other to measure single-wavelength interferogram. In this design, the instantaneous interference intensity as well as OPD can be obtained in an accurate way so that the exact spatial interferogram of the incident spectrum can be worked out. Consequently, the incident spectrum can be retrieved by FT method. A resolution of 7.69 cm-1 in the wavelength range of 1400 nm ∼ 1700 nm is achieved. Experimental results show that the performance of our device is comparable to the commercial benchtop spectrometer. Our device is independent of the complicated fabrication procedures, easy of usage, and cost effective. We envision that the proposed design will inspire a new concept for constructing simple and cheap spectrometers that is well suited for practical applications.
Miniaturized fiber Fabry–Pérot interferometer for strain sensing

Yajun Jiang,Jian Xu,Dexing Yang,Kai Zhang,Dong Li,Jianlin Zhao

DOI: https://doi.org/10.1002/mop.29821

IF: 1.311

2016-01-01

Microwave and Optical Technology Letters

Abstract:A temperature-insensitive miniaturized all-fiber Fabry-Perot interferometer strain sensor was proposed and experimentally studied. This sensor with an air cavity was made by splicing a short section of hollow-core fiber with two standard single mode fibers. The experimental results showed that these sensors have an fringe contrast exceeding 22 and 13 dB for the air cavity with a length of 167.08 and 557.11 m, and its reflection spectrum shifts linearly to long wavelength by increasing the strain from 0 to 3000 epsilon with a strain sensitivity of 1.8 and 1.7 pm/epsilon, respectively. This strain sensor also showed good repeatability and long time stability, while its temperature sensitivity was only about 0.95 pm/degrees C in the range of 0 degrees C-180 degrees C for the 557.11 m air cavity, so there is less strain-temperature cross-sensitivity. Moreover, this sensor was easy to be fabricated and there was no requirement for chemical etching, careful cleaving, and special fusion. It may be potentially used for strain sensing applications with high resolution and miniaturized size. (c) 2016 Wiley Periodicals, Inc. Microwave Opt Technol Lett 58:1510-1514, 2016
High pressure-sensitive and stable fiber Fabry-Perot interferometer with nano-diaphragm assembled by H-O catalysis bonding

Xiaotong Li,Xinpu Zhang,Zeliu Li,Yisong Wang,Jiamai Ren,Ang Li,Fenglin Zhang,Wei Peng

DOI: https://doi.org/10.1364/oe.516004

IF: 3.8

2024-03-08

Optics Express

Abstract:Xiaotong Li, Xinpu Zhang, Zeliu Li, Yisong Wang, Jiamai Ren, Ang Li, Fenglin Zhang, Wei Peng Herein, a high pressure-sensitive and stable fiber Fabry-Perot (FP) interferometer with nano-diaphragm assembled by H-O catalysis bonding ... [Opt. Express 32, 10219-10229 (2024)]

optics
Miniature Fiber Pressure Sensor Based on an In-Fiber Confocal Cavity

Tingting Wang,Yixian Ge,Haibin Ni,Jianhua Chang,Jiahong Zhang,Wei Ke

DOI: https://doi.org/10.1016/j.ijleo.2018.06.151

IF: 3.1

2018-01-01

Optik

Abstract:A new type of miniature pressure sensor based on a hybrid Fabry-Perot (F-P) interferometer is proposed. The in-line air cavity of the sensor is a micro-confocal air cavity, which is formed by splicing together a single mode fiber (SMF) and a solid-core photonic crystal fiber (PCF) with the specific splicing parameters. The sensor is fabricated by simple steps involving only fusion splicing, cleaving and polishing. Optical interference principle of the sensor is analyzed and the parameters in sensor design are discussed. Due to low propagation loss, experiments show that the reflection spectrum of the sensor has a fringe contrast of more than 30 dB. By tracing the trough wavelength in the interference spectrum, the pressure can be demodulated. Within the pressure measurement range of 0-1 MPa, the sensitivity is -193 pm/MPa. The experimental results indicate that the deflection is consistent with the theoretical analysis and the sensor has a good linearity. Easy fabrication, low-cost and high-contrast make it appropriate for practical application.
A Miniaturized Spectrometer Based on Optical Modulator Composed of Grating and Tunable Fabry-Perot

Naike Wei,Zhugao Ni,Jun Yao,Jianhua Zhu,Fuhua Gao

DOI: https://doi.org/10.4028/www.scientific.net/kem.483.447

2011-01-01

Key Engineering Materials

Abstract:In this paper an innovative miniaturized spectrometer has been presented. The structure is similar to a grating spectrometer, but its optical modulator is composed of a grating and a tunable Fabry-Perot (FP). The collimated light is diffracted by the grating and filtered by the FP, and interference fringes distribute separately on the focal plane. The position of fringes moves when the FP is tuned, this helps in the scanning and detecting of the peak wavelength of fringes. The principle and characteristics of the spectrometer are discussed in detail.

Miniature All-Fiber Fabry-Perot Interferometer

Angled Fiber-Based Fabry–Perot Interferometer

All-Fiber Fabry-Perot Resonators Based on Microfiber Sagnac Loop Mirrors

Angled Fiber-Based FP Interferometer

Miniaturized Fiber Inline Fabry-Perot Interferometer Fabricated with A Femtosecond Laser

Chirped Fiber Tip Fabry-Perot Interferometer.

In-line All-Fiber Fabry-Perot and Mach-Zehnder Interferometers Formed by Hollow Fiber with Lateral Offset

In-Fiber Fabry–Perot and Mach–Zehnder Interferometers Based on Hollow Optical Fiber Fabricated by Arc Fusion Splicing with Small Lateral Offsets

Ultra-small Fiber Taper Fabry-Perot Modal Interferometer

Novel miniaturized fabry-perot refractometer based on a simplified hollow-core fiber with a hollow silica sphere tip

Miniature Fabry-Perot Interferometer Based on a Movable Microsphere Reflector.

Fiber Fabry-Perot Interferometer with Controllable Temperature Sensitivity

High-temperature resistant, all-fiber miniature interferometer

Miniature Fabry-Perot interferometric sensor for temperature measurement based on photonic crystal fiber

All-fiber Miniature Fabry-Perot Interferometer As High Temperature Sensor

Intrinsic Fiber-Optic Fabry-Perot Interferometer Based On Arc Discharge And Single-Mode Fiber

Miniature Fourier Transform Spectrometer Based on a Fiber-Tip Interferometer.

Miniaturized fiber Fabry–Pérot interferometer for strain sensing

High pressure-sensitive and stable fiber Fabry-Perot interferometer with nano-diaphragm assembled by H-O catalysis bonding

Miniature Fiber Pressure Sensor Based on an In-Fiber Confocal Cavity

A Miniaturized Spectrometer Based on Optical Modulator Composed of Grating and Tunable Fabry-Perot