Abstract:Austenite stability is essentially important in improving the cryogenic toughness of cryogenic Ni steels and guiding the development of Ni-saving cryogenic steels. The austenite stability in the cryogenic Ni steels is influenced by many microstructure features, making it a complicated issue which is lack of a systematic discussion. In this article, the microstructural effects on the thermal and mechanical stability of austenite in the cryogenic Ni steels are reviewed and discussed. The thermal stability of austenite (TSA) will be enhanced by the enrichment of austenite-stabilizing elements in the austenite which decreases the martensite-start (Ms) temperature. The grain refinement enhances the TSA by synergistically increasing the nonchemical driving force for the martensite transformation and the concentrations of austenite-stabilizing elements in the austenite. The excessive increase in the volume fraction of austenite weakens the TSA by decreasing the concentrations of austenite-stabilizing elements in the austenite. The film austenite is usually thermally more stable than the block austenite owing to its higher concentrations of austenite-stabilizing elements. The mechanical stability of austenite (MSA) is also influenced by the concentrations of austenite-stabilizing elements which affect the Ms temperature. The reports on the effect of grain size of austenite on the MSA are inconsistent. Both negligible and important effects of the grain size of austenite on the MSA are analyzed. The grain orientation of austenite affects the MSA via changing the Schmid factor and the additional driving force for the martensite transformation. The orientation which yields a larger value of Schmid factor would exhibit a lower MSA. The MSA is affected by the matrix or the neighboring phase due to the stress and strain partitioning among austenite and other constituent phases. The dislocation multiplication could weaken the MSA by assisting the nucleation and growth of martensite embryo and enhance the MSA by hindering the motion of embryo/austenite interfaces when dislocation density is sufficiently large. Austenite with a combination of a high TSA and a moderate or high MSA is considered to be effective strategies to enhance cryogenic toughness of the cryogenic Ni steels.

Effect of Microstructure Synergism on Cryogenic Toughness for CGHAZ of Low-Carbon Martensitic Steel Containing Nickel

Effect of grain size and segregation on the cryogenic toughness mechanism in heat-affected zone of high manganese steel

Effect of Gradient Microstructure and Strength Mismatch on Cryogenic Toughness of Fe-Ni Fusion Boundary

Factors Influencing Notch Toughness of Coarse-grained Heat Affected Zone for 9% Ni Steel

Effects of Small Ni Addition on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of High-Strength Low-Alloy Steel

Grain Size Dependence of Twinning Behaviors and Resultant Cryogenic Impact Toughness in High Manganese Austenitic Steel

Effect of aging temperature on the austenite reversion and mechanical properties of a Fe–10Cr–10Ni cryogenic maraging steel

Precipitation behavior of carbides and cryogenic toughness in heat-affected zone of high-Mn twinning-induced plasticity steel welded joint

Interpretation of Significant Decrease in Cryogenic-Temperature Charpy Impact Toughness in a High Manganese Steel

Tailoring the Microstructure to Enhance the Cryogenic Mechanical Properties of a Fe–34.5mn–0.04c Steel

Cryogenic Toughness in a Low-Cost Austenitic Steel

On the austenite stability of cryogenic Ni steels: microstructural effects: a review

Effect of aging temperature on the heterogeneous microstructure and mechanical properties of a 12Cr–10Ni–Mo–Ti maraging steel for cryogenic applications

Enhancing Ductility of Martensitic Steels Through Cryogenic Treatment

Study of Cryogenic Treatment on the Microstructure and Mechanical Properties of Marine 10Ni5CrMoV Steel

Influence of banded ε-martensite and deformation twin on cryogenic toughness of Fe-Mn-xAl-C steel

Effect of Initial Microstructure on the Toughness of Coarse-Grained Heat-Affected Zone in a Microalloyed Steel

The Role of Retained Austenite on the Mechanical Properties of a Low Carbon 3Mn-1.5Ni Steel

Design of Novel Fe–Mn–Ni Cryogenic Steel: Microstructure-Property Relationship During Simulated Welding

Effects of deformation-induced martensitic transformation on cryogenic fracture toughness for metastable Si8V2Fe45Cr10Mn5Co30 high-entropy alloy

Correlations of Ni Contents, Formation of Reversed Austenite and Toughness for Ni-Containing Cryogenic Steels