Abstract:Condensation heat transfer characteristics (using R410A as the working fluid) were studied experimentally to evaluate the heat transfer performance in copper and stainless-steel heat transfer tubes (smooth and enhanced). Experiments were carried out for a mass flux that varied from 250 to 450 kg m−2 s−1, at a saturation temperature of 318 K. Single-phase heat balance verification found that the heat loss is less than 6%, and the deviation between single-phase experimental results and various prediction correlations is less than 15%. Additionally, tube side condensation flow patterns were observed and recorded. Experimental results found that the enhancement ratio of the condensation heat transfer coefficient (enhanced tube/smooth tube) of the three-dimensional surface (1EHT) tube is in the range of 1.15~1.90, while the ratio of the micro-fin (HX) tube is in the range of 1.18~1.80. Heat transfer performance is affected by material conductivity, with the thermal conductivity of the smooth tube slightly affecting the heat transfer performance; larger heat transfer enhancements are produced in the enhanced tubes. At a low mass flow rates and vapor qualities, the flow pattern is a stratified wavy flow, while at higher mass flow rates and vapor qualities, the flow pattern is an annular flow (with the area in the enhanced tube being larger than the area of a smooth tube). Flow patterns in the smooth tube are consistent with the predicted values shown in previously reported flow pattern maps. A flow pattern diagram for condensation heat transfer in enhanced tubes is presented as part of this study. The condensation heat transfer coefficient increases with an increase in mass flow. When the mass flow rate increases, the turbulence of the liquid flow increases and the liquid film becomes thinner; thermal resistance is reduced and the heat transfer coefficient increases. Heat transfer values at lower mass velocities increase slightly with increasing mass flux values; however, at higher mass flux rates the heat transfer increase is larger than that at low mass flux values. Finally, tubes produced from high thermal conductivity materials produce larger heat transfer performance gains than the gains found in smooth tubes; small diameter tubes produce larger gains than larger diameter tubes.

Visualization of R410A Flowing in Copper and Stainless Steel Dimpled Tubes Enhanced by Petal-Shaped Patterns under Evaporation Conditions

Evaporation flow patterns and heat transfer in copper and stainless steel three-dimensional dimpled tubes

Evaporation Heat Transfer Characteristics of R410A Inside Horizontal Three-Dimensional Enhanced Tubes

Evaporation Flow Heat Transfer Characteristics of Stainless Steel and Copper Enhanced Tubes

Two-phase Heat Transfer in Horizontal Dimpled/protruded Surface Tubes with Petal-Shaped Background Patterns

Visualization of Flow Patterns During Condensation in Dimpled Surface Tubes of Different Materials

Experimental Investigation of Flow Boiling Inside Three Three-Dimensional Surface Enhanced Heat Transfer Tubes

Visualization of R1233zd(E) Flow Boiling in Parallel Mini-channels

Experimental Study on Condensation and Evaporation Flow Inside Horizontal Three Dimensional Enhanced Tubes

Condensation and Evaporation Heat Transfer Characteristics of Low Mass Fluxes in Horizontal Smooth Tube and Three-Dimensional Enhanced Tubes

Condensation Heat Transfer Experiments of R410A and R32 in Horizontal Smooth and Enhanced Tubes

Condensation Flow Heat Transfer Characteristics of Stainless Steel and Copper Enhanced Tubes

Eexperimental Study On Flow Evaporation Heat Transfer Characteristics Inside Horizontal Three-Dimensional Enhanced Tubes

Analysis of Condensation and Evaporation Heat Transfer Inside 3-D Enhanced Tubes

Condensation Flow and Heat Transfer Characteristics of R410A in Micro-Fin Tubes and Three-Dimensional Surface Enhanced Tubes

R410A Flow Condensation Inside Two Dimensional Micro-Fin Tubes and Three Dimensional Dimple Tubes

Condensation and Evaporation Heat Transfer Characteristics in Horizontal Smooth and Three-Dimensional Enhanced Tubes

Experimental Study on Heat Transfer Performance and Flow Pattern in Micro-Fin Tubes and 1EHT Three-Dimensional Heat Exchange Tubes

Condensation and Evaporation Heat Transfer Characteristics in Horizontal Smooth, Herringbone and Enhanced Surface EHT Tubes

Condensation Characteristics of Flows Inside the Three-Dimensional Enhanced and Smooth Tubes

Condensation Heat Transfer of R410A on Outside of Horizontal Smooth and Three-Dimensional Enhanced Tubes