Abstract:A horizontal smooth copper tube and two enhanced tubes (a dimpled tube and a diamond-shaped tube) with a length of 2 m and an outer diameter of 9.52 mm were studied in a two-phase condensation experiment using R410A and R32 as heat transfer working fluids. The condensation heat transfer performance of different heat transfer tubes at various mass fluxes ranging from 150 to 400 kg/(m(2)s) and different vapor qualities ranging from 0.8 to 0.2 was studied experimentally. For R410A, the heat transfer coefficients (HTCs) of the dimpled tube and the diamond-shaped tube were found to be 1.39-1.52 times and 1.30-1.35 times higher than those of the smooth tube, respectively. For R32, the HTCs were found to be 1.46-1.59 times higher for the dimpled tube and 1.26-1.35 times higher for the diamond-shaped tube than for the smooth tube. The diamond-shaped tube was found to be effective in directing the flow of the liquid phase and in thinning the liquid film thickness. The dimpled tube was found to promote droplet entrainment and disturbance. Both of those effects contributed to improving the HTCs in the two enhanced tubes investigated. The HTCs of R410A were found to be lower than those of R32 because of the smaller specific heat capacity, smaller latent heat of condensation, and relatively poorer thermal conductivity of R410A. Taking the combined effect of heat transfer and pressure drop into account, a performance enhancement factor (PEF) was computed and was found to range from 0.9 to 1.51. Based on the experimental data collected, a new empirical correlation equation has been proposed with a maximum error band of 10%. Flow pattern maps for the tested tubes have also been generated and are presented in the paper. Both of the two enhanced tubes were found to promote the development of annular flow. The HTCs were found to be highest when the flow pattern was of the annular flow type.

Two-phase Heat Transfer in Horizontal Dimpled/protruded Surface Tubes with Petal-Shaped Background Patterns

Experimental Study on Condensation and Evaporation Flow Inside Horizontal Three Dimensional Enhanced Tubes

Experimental Study Of Condensation Flow Inside Horizontal Smooth, Herringbone And Three Enhanced Surface Tubes

Condensation and Evaporation Heat Transfer Characteristics in Horizontal Smooth, Herringbone and Enhanced Surface EHT Tubes

Condensation Heat Transfer in Horizontal Three Dimensional Two-Layer Two-Side Enhanced Tubes

Visualization of R410A Flowing in Copper and Stainless Steel Dimpled Tubes Enhanced by Petal-Shaped Patterns under Evaporation Conditions

Condensation Heat Transfer Experiments of R410A and R32 in Horizontal Smooth and Enhanced Tubes

Condensation Heat Transfer in Smooth and Three-Dimensional Dimpled Tubes of Various Materials

Experimental Investigation of Flow Boiling Inside Three Three-Dimensional Surface Enhanced Heat Transfer Tubes

Analysis of Condensation and Evaporation Heat Transfer Inside 3-D Enhanced Tubes

Condensation and Evaporation Heat Transfer Characteristics in Horizontal Smooth and Three-Dimensional Enhanced Tubes

Condensation heat transfer in annuli outside horizontal stainless steel enhanced tubes

An Experimental Study of In-Tube Condensation and Evaporation Using Enhanced Heat Transfer (EHT) Tubes

Condensation and Evaporation Heat Transfer Characteristics of Low Mass Fluxes in Horizontal Smooth Tube and Three-Dimensional Enhanced Tubes

R410A Flow Condensation Inside Two Dimensional Micro-Fin Tubes and Three Dimensional Dimple Tubes

Evaporation Heat Transfer Characteristics of R410A Inside Horizontal Three-Dimensional Enhanced Tubes

Condensation Heat Transfer of R410A on Outside of Horizontal Smooth and Three-Dimensional Enhanced Tubes

Condensation Heat Transfer Characteristics On The Outside Of Horizontal Smooth, Herringbone And Enhanced Surface 1eht Tubes

Condensation Characteristics of Flows Inside the Three-Dimensional Enhanced and Smooth Tubes

Evaporation flow patterns and heat transfer in copper and stainless steel three-dimensional dimpled tubes

Evaporation Heat Transfer Characteristics On The Outside Of Horizontal Smooth, Herringbone And Enhanced Surface 1eht Tubes