Abstract:Methanol synthesis from CO2 hydrogenation has drawn global attention as catalytic CO2 hydrogenation is an attractive choice to mitigate CO2 emissions and lessen dependency on fossil resources. In the present study, we have synthesized ZrO2 and CeO2 supported In2O3 catalysts for methanol synthesis from CO2 hydrogenation and the catalytic performances of Inx/ZrO2, and Inx/CeO2 (x = 1% and 13%) were compared. Specifically, the effect of the ZrO2 and CeO2 supports on In2O3 catalyst during CO2 hydrogenation was explored. This study reveals that ZrO2 support increased the catalytic activity while the CeO2 support decreased although both supports have almost the same indium loading and surface area. Various characterizations like XRD, DRIFT, CO2-TPD, H2-TPR and XPS analysis of catalysts provided insight into changes that arise after mixing the two oxides and during the reaction as well as after the reaction. The stabilities of In2O3, In13/ZrO2 and In13/CeO2 were tested for up to 12 h and we found In2O3, In13/ZrO2 was stable during this time-on-stream, while In13/CeO2 lost activity after 2 h of reaction. XPS results of spent catalyst showed that the metal hydroxides increased significantly for the spent In13/CeO2. OH-groups were also verified by DRIFT experiments, however at low levels due to low CO2 conversion at atmospheric pressure. A regeneration study was carried out to regenerate the catalyst and the results showed that partial regeneration of the In13/CeO2 catalyst is possible by Ar flushing. We therefore suggest that the build-up of OH groups deactivate the In13/CeO2 catalyst and some of these OH groups could be removed during flushing with inert gas, causing a partial regeneration. However, the structural changes and decreased surface area is not reversible, and this results in a continuous decrease in activity of the catalyst after repeated experiments, even if the catalyst is flushed with Ar between the experiments.

Influence of Mn and Mg Oxides on the Performance of In2O3 Catalysts for CO2 Hydrogenation to Methanol

Theoretical Investigation on the CO2 Hydrogenation to Methanol Mechanism at Electron-Rich Active Interface over Cu/Ga-Ti-Al-O Catalyst

Co- and Ni-promoted indium oxide for CO2 hydrogenation to methanol

Effect of In2O3 on the structural properties and catalytic performance of the CuO/ZnO/Al2O3 catalyst in CO2 and CO hydrogenation to methanol

The influence of Mg/Al molar ratio on the performance of CuMgAl-x catalysts for CO2 hydrogenation to methanol

CO 2 Hydrogenation to Methanol over In 2 O 3 : The Size Effect

Effect of the Preparation Methods on the Physicochemical Properties of Indium-Based Catalysts and Their Catalytic Performance for CO 2 Hydrogenation to Methanol

Nickel-modified In2O3 with inherent oxygen vacancies for CO2 hydrogenation to methanol

Highly Active and Stable Mixed-Phase In2O3-supported Ni Catalyst for CO2 Hydrogenation to Methanol

Carbon coated In2O3 hollow tubes embedded with ultra-low content ZnO quantum dots as catalysts for CO2 hydrogenation to methanol

Rationally Designed Indium Oxide Catalysts for CO2 Hydrogenation to Methanol with High Activity and Selectivity

Enhanced Surface Charge Localization Over Nitrogen-Doped In 2 O 3 for CO 2 Hydrogenation to Methanol with Improved Stability

Recent Advances of Indium Oxide-Based Catalysts for CO2 Hydrogenation to Methanol: Experimental and Theoretical

Methanol Synthesis from CO2 Hydrogenation over Copper Catalysts Supported on MgO-modified TiO2

CO2 hydrogenation to methanol over Pd/MnO/In2O3 catalyst

Nickel-modified in 2 O 3 with Inherent Oxygen Vacancies for CO 2 Hydrogenation to Methanol

Role of Zro2 and Ceo2 Support on the In2o3 Catalyst Activity for Co2 Hydrogenation

The Promoting Role of Ni on In2O3 for CO2 Hydrogenation to Methanol

CO2 hydrogenation to methanol over the copper promoted In2O3 catalyst

Towards Maximizing the In2O3/m-ZrO2 Interfaces for CO2-to-methanol Hydrogenation.

Al Promotion of In2O3 for CO2 Hydrogenation to Methanol