Abstract:Synergistic effects of silane‐modified carbon black and nano‐silica hybrid fillers on the performance of EPDM rubber composites. This study assesses the effectiveness of a specially developed surface‐modified carbon black, both on its own and in combination with nano‐silica, as a hybrid filler for ethylene–propylene–diene monomer (EPDM) rubber compounds. The modification process, which included treatment with a silane coupling agent, resulted in enhanced curing characteristics. The ∆Torque values for compounds incorporating the modified carbon black exceeded those of other formulations by 25.85%. Scanning electron microscopy (SEM) analysis demonstrated improved filler dispersion and better compatibility between rubber and filler due to the surface modification. The silane‐modified carbon black showed considerable enhancements in mechanical properties, particularly in tear resistance, with increases in tensile and tear strength of 22.46% and 34.86%, respectively, following surface treatment. Dynamic mechanical analysis (DMA) indicated the influence of both surface modification and filler type, revealing that the combination of modified carbon black and nano‐silica achieved a reduction in rolling resistance of 20.41% and enhanced ice and wet grip performance by 7.95%. Additionally, modified carbon black displayed varying effects on the glass transition temperature. Thermal gravimetric analysis (TGA) confirmed that the thermal stability of the compounds was consistent, while solvent resistance improved with surface modification, as shown by swelling ratios. Thermodynamic analysis indicated that the surface modification of carbon black positively influences the elasticity and chain mobility of the rubber compounds studied. In conclusion, the careful selection and optimization of filler materials and their modifications are essential for customizing the properties of rubber compounds to satisfy specific performance criteria and applications. Highlights Promising EPDM compounds were prepared with Silane‐Modified CB and Nano‐Silica. Silane‐modified CB effectively improved the curing properties of the EPDM compound. The ΔTorque and cross‐link density of modified CB/EPDM show the highest value. Modified CB/Nano‐Silica/EPDM exhibited significant improvement in tear strength. Modified CB/Nano‐silica/EPDM have lower rolling resistance and higher wet grip.

Mechanical Properties of Silicone Rubber Enhanced Microcellular EPDM Foams Based on Supercritical CO2 Foaming Technology

Microstructure and Properties of Microcellular Silicone Rubber Foams with Improved Surface Quality

Mechanical properties of microcellular and nanocellular silicone rubber foams obtained by supercritical carbon dioxide

Preparation and properties of silicone rubber materials with foam/solid alternating multilayered structures

Effect of silica particles on vulcanization performance, viscoelasticity and cell structure of EPDM

The Effects of a Crosslinking Agent on the Microrheological Properties and Cellular Structure of Silicone Rubber Foam Prepared via a Green Process

Microcellular silicone rubber foams: The influence of reinforcing agent on cellular morphology and nucleation

Mechanical Properties and Mullins Effect of Ethylene Propylene Diene Monomer Vulcanizes Reinforced with Silica Powders with Different Micropore Structures

Synthesis of Monodisperse Mesoporous Carbon Spheres/EPDM Rubber Composites and Their Enhancement Mechanical Properties

Porous structures design in liquid silicone rubber foams through CO 2 controlled molecular crosslinking

Key Factors for Regulation of Cell Morphology in Supercritical CO2 Direct Rapid Depressurization Foaming Silicone Rubber Process

Design and preparation of novel silicon rubber with homogeneous crosslinking network and its application in high-performance SR/EPDM blend

Aramid fiber reinforced EPDM microcellular foams: Influence of the aramid fiber content on rheological behavior, mechanical properties, thermal properties, and cellular structure

Solid‐state Microcellular High Temperature Vulcanized (HTV) Silicone Rubber Foam with Carbon Dioxide

Solid-state microcellular high temperature vulcanized (HTV) silicone rubber foam with carbon dioxide: REIVEW

Effect of polydiborosiloxane on the mechanical properties of silicone rubber foam with dual network structure

Physical Properties of Microcellular Polymeric Foams with Supercritical CO2

Preparation of Open-Cell Polymer Foams by CO2 Assisted Foaming of Polymer Blends

Sulfur Free Crosslinking of EPDM Composites via Silane Grafting and Silica Incorporation

The effect of silane‐modified carbon black and nano‐silica, individually and in combination, on the performance of ethylene–propylene–diene monomer rubber

The relationship between cellular microstructure and the mechanical properties of styrene/methyl methacrylate copolymer‐silica nanocomposite foams prepared by a supercritical CO2 blowing agent