Abstract:Styrene/methyl methacrylate copolymer‐silica nanocomposite foams were prepared using supercritical CO2 as blowing agent, and the relationships between their cellular microstructure and mechanical properties were investigated. Styrene/methyl methacrylate (St/MMA) copolymer‐silica nanocomposite foams were prepared using supercritical CO2 as blowing agent, and the relationships between their cellular microstructure and mechanical properties were investigated. The effects of nanosilica content, size, and surface chemistry on the foam's microstructure and properties were examined. Dispersion and distribution of silica nanoparticles with different surface chemistry in St/MMA copolymer nanocomposites were discussed. To determine the most suitable copolymer composition for incorporating silica nanoparticles, some operating conditions such as temperature and pressure were primarily examined to study their effects on the microstructure of resulting foams. In compressive mechanical properties of final foams, a considerably high value was obtained for the compressive strength of the foams of up to 9.5 MPa. The prepared low‐density (below 0.2 g/cm3) St/MMA copolymer microcellular foams can be used in green lost foam iron casting processes. Highlights Styrene/methyl methacrylate copolymer‐silica nanocomposite foams were prepared via supercritical CO2. Foams' cell size was changed by changing silica nanoparticle surface chemistry and size. The uniform cellular microstructure was achieved by nanosilica size increment. Increasing nanoparticle size improved the foam's mechanical properties. Low‐density foams were achieved for potential application in lost foam casting.

Effects of scCO2 foaming process and post‐vulcanization method on cellular structure, mechanical properties, and thermal stability of PMVQ foams

Effect of Melt Viscosity on the Cell Morphology and Properties of Poly(lactic Acid) Foams

Study on the Foaming Behaviors of PBS and its Modification with PA6IcoT Assisted by scCO2

Preparation and Density Control of Pmma Microcellular Foams Via Supercritical Carbon Dioxide Foaming

Effect of Plasticizer on the Morphology and Foaming Properties of Poly(vinyl alcohol) Foams by Supercritical CO2 Foaming Agents

Ultrasound and H2O assisted scCO2 foaming technology for preparation of PS/PMMA composite foams with ultra-lightweight and super thermal-insulation

Producing microporous PMMA with supercritical CO 2 and the research on its properties

Effect of Vulcanization and CO2 Plasticization on Cell Morphology of Silicone Rubber in Temperature Rise Foaming Process

Producing Microporous PMMA with Supercritical CO2 and the Research on Its Properties

Microstructure and Properties of Microcellular Silicone Rubber Foams with Improved Surface Quality

Microcellular PETs with High Expansion Ratio Produced by Supercritical CO2 Molding Compression Foaming Process and Their Mechanical Properties

Solid-state microcellular high temperature vulcanized (HTV) silicone rubber foam with carbon dioxide: REIVEW

Solid‐state Microcellular High Temperature Vulcanized (HTV) Silicone Rubber Foam with Carbon Dioxide

Mechanical Properties of Silicone Rubber Enhanced Microcellular EPDM Foams Based on Supercritical CO2 Foaming Technology

Microcellular Foaming of Polysulfones in Supercritical CO2 and the Effect of Co-Blowing Agent

Microcellular Thermoplastic Polyurethanes and Their Flexible Properties Prepared by Mold Foaming Process with Supercritical CO2

Effect of Prevulcanization Process on Properties of EPDM Foam

Key Factors for Regulation of Cell Morphology in Supercritical CO2 Direct Rapid Depressurization Foaming Silicone Rubber Process

Research Process of Microcellular Foams Prepared by Supercritical Fluid Technique

The relationship between cellular microstructure and the mechanical properties of styrene/methyl methacrylate copolymer‐silica nanocomposite foams prepared by a supercritical CO2 blowing agent

The Degradation Effect of Complex Conditions on Polymethyl-Vinyl Siloxane Foam