Abstract:Gas distributor is a key component in fluidized beds. Various gas distributors for practical application have been successfully developed and studied in depth. Fluidization of coarse particles is still a challenge for good gas-solid contacting. In this study, a slotted gas distributor with simple structure was proposed for the fluidized bed processing coarse particles. The fluidization characteristics of the Geldart D type large particles (2-2.8 mm walnut shell) were investigated experimentally in a 285 mm × 190 mm × 700mm fluidized bed with the slotted gas distributor whose opening rate was 5.6%. The experimental results were compared with the ones obtained from the traditional perforated distributor. It was found that the bed expansion ratio increased by about 5% and the minimum fluidization velocity reduced by about 8% when using the slotted gas distributor, indicating that the slotted gas distributor had better fluidization characteristics for the large-sized particles. To explain the better fluidization performance of the slotted gas distributor, a computational fluid dynamics (CFD) model was developed based on the Eulerian-Eulerian model, the particle kinetic theory, the standardk-ε turbulence model and the SIMPLE algorithm. The CFD model was used to simulate the behaviors of the gas particle flow in the fluidized bed of walnut shell particles with slotted gas distributor or traditional perforated distributor, and the results of experiment and simulation were agreed well. The simulations were conducted under such operation conditions: The physical two-dimensional model of the rectangular fluidized bed was 285 mm × 700 mm with slotted gas distributor or traditional perforated distributor in which the opening rate was 5.6%. Particles packed in the fluidized bed had the volume fraction of 0.6 and the height of the bed was 200 mm. The superficial gas velocity of inlet was selected as operation parameter, which ranged from 0.615 to 1.128 m/s. The simulation results were compared on the bed pressure fluctuations due to bubble formation, the coalescence and eruption, the maximum bed expansion radio, the transient particle volume fraction distribution, the gas/particle velocity vector distribution and so on between the fluidized beds of these two distributors. It was observed that small bubbles first formed close to the gas distributor, coalesced when rising up, and finally erupted near the bed surface, which resulted in periodic fluctuations of bed pressure with different amplitudes and frequencies. Compared with the traditional perforated distributor, the frequency and amplitude of the bed pressure drop fluctuation caused by the slotted gas distributor were bigger and the bed expansion ratio was higher. The change of the particle concentration in the bed was scattered in the fluidized bed with slotted gas distributor, which was beneficial to the fluidization of particles near the bed wall. Also, the dead zone and recirculation area formed near the wall area were reduced. The V-shaped structure of the slotted gas distributor generated strong upward flow jets. The strong jets could deeply reach the material particle bed and easily bring the formation of bigger bubbles. The bigger bubbles caused more intensive disturbance inside the material bed, and thereby the bed pressure drop fluctuation and the bed expansion ratio were improved. Four small circulations were observed to form within the fluidized bed with slotted gas distributor, which was beneficial to the better mixing of gas and particle. Therefore, coarse particles of walnut shell can be well fluidized with the slotted gas distributor. The study provides a reference for the design and selection of fluidized bed distributor in the process of coarse particle processing in fluidized bed.

Hydrodynamic Behaviors of a Spouted Fluidized Bed with a Conical Distributor and Auxiliary Inlets for the Production of Polysilicon with Wide-Size-distribution Particles

Dynamic and Steady-State Characterization of the Liquid Spray Zone in an Externally Heated Gas–Solid Fluidized Bed

Particle Fluidization Characteristics and Transition in a Hot Gas-Solid Fluidized Bed with Liquid Injection

Distribution and Movement of Fine Particles Injected in a Gas–solid Fluidized Bed with Hydrocarbon Liquid Spray

Experimental Investigation of Bubble and Particle Motion Behaviors in A Gas-Solid Fluidized Bed with Side Wall Liquid Spray

Characterization of Flow Pattern of Cohesive Particles in Gas-Solid Fluidized Bed Via Axial Distribution of Particle Motions

Dispersion Trajectory and Dynamics of Particles Injected from the Sidewall in the Gas–Solid Fluidized Bed

Hydrodynamic behaviors of an internally circulating fluidized bed with wide-size-distribution particles for preparing polysilicon granules

CFD Simulation of the Hydrodynamic Behavior in an Internally Circulating Fluidized Bed Reactor for Producing Polysilicon Granules

Numerical simulation of granular silicon growth and silicon fines formation process in polysilicon fluidized bed

Bubble Dynamics and Particle Orientation in a Binary Fluidized Bed Containing Spherocylinders and Spheres

Experimental Research on the Gas-Solid Flow Characteristics in Large-Scale Dual Fluidized Bed Reactor

Fluidization of coarse particles in gas–solid conical beds

Study on Internal Circulation Fluidized Bed Reactor for Preparing Polysilicon Granules

CFD-DEM Simulation of High Density Particles Fluidization Behaviors in 3D Conical Spouted Beds

Influence of Silicon Size Distribution on Hydrochlorination Process of Solar-grade Silicon in Spouted Reactor via MP-PIC Approach

Fluidization Characteristics of Silicon Particles with a Wide Size Distribution

Method for preparing high purity polysilicon particle with fluidized bed and bed fluidizing reactor

Particle‐scale Investigation of the Solid Dispersion and Residence Properties in a 3‐D Spout‐fluid Bed

Numerical Study on the Gas–Solid Flow in a Spouted Bed Installed with a Controllable Nozzle and a Swirling Flow Generator

Fluidization Effect of Walnut Shell Particles in Fluidized Bed with Slotted Gas Distributor