Abstract:Selective laser melting (SLM) has been widely used to manufacture customised metallic parts because it provides an integrated way to manufacture three-dimensional (3D) parts from computer-aided design models after several sub-processes. On the other hand, aluminium-based nanocomposites are widely used in the aerospace and automotive industries due to their light weight, high specific strength, excellent wear resistance, but their manufacturability and mechanical properties are not well understood when these new materials are employed in SLM. This is an important consideration because, compared with traditional manufacturing technologies, SLM offers the ability to manufacture engineering parts with very complex geometries by employing a layer-by-layer manufacturing principle. Hence, this thesis systematically studies the SLM of an advanced Al-Al2O3 nanocomposite that is synthesised using high-energy ball-milling (HEBM) process. The aim of this study is to use SLM to fabricate a nearly full dense Al-Al2O3 nanocomposite composed of 96 vol.% Al and 4 vol.% Al2O3 powder. The synthesis and characterisation of ball-milled powder is the first contribution of this study, which also investigates the influence of milling and pause duration on the fabrication of ball-milled composite powder. The second contribution of this work is the development of a 3D finite element model to predict the thermal behaviour of the first layer’s composite powder. Both the transient temperature distribution and molten pool dimensions are predicted within the laser scanning, which VI enables a more efficient selection of the process parameters (e.g. hatch spacing and scanning speed). The third contribution of this study is the optimisation of the SLM process parameters and microstructure investigation of the fabricated samples. The optimum laser energy density and scanning speed that are used to fabricate nearly full dense Al-Al2O3 nanocomposites are found to be 317.5 J/mm3 and 300 mm/s, respectively. The relative density is evaluated by quantifying the porosity on both the horizontal and vertical sections. The fabricated composite parts were observed to exhibit a very fine granular-dendrite microstructure due to the rapid cooling, while the thermal gradient at the molten pool region along the building direction was found to facilitate the formation of columnar grains. The final contribution of this study is the investigation of mechanical properties such as tensile strength, microhardness and macro and nanoscale wear behaviour. Compared to pure Al, the addition of 4 vol.% Al2O3 nanoparticulates was found to contribute to a 36.3% and 17.5% increase in the yield strength and microhardness of the composite samples, respectively. Cold working was found to contribute to a 39% increase in microhardness due to grain deformation. The pin-on-disc wear testing and atomic force microscopy (AFM) nanoscratching were performed to study the macro and nanoscale wear behaviour of the fabricated samples, respectively.

Laser Heat Assisted Machining Characteristics Of Al2o3 Particle-Reinforced Al-Matrix Composite

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Laser Based Machining of Aluminum Metal Matrix Composites

Mechanisms involved in the tool life improvement of laser assisted machining 45%SiCp/Al composites

High speed, high power density laser-assisted machining of Al-SiC metal matrix composite with significant increase in productivity and surface quality

Water-jet guided laser drilling of SiC reinforced aluminium metal matrix composites

Effect of reinforced particles on the machinability of Al alloy under MQL, cryogenic, and hybrid lubrication

Development of metal matrix composites by laser-assisted additive manufacturing technologies: a review

A Study on the Laser-Assisted Machining of Carbon Fiber Reinforced Silicon Carbide

Microstructure evolution and mechanical properties of Al-Al2O3 composites fabricated by selective laser melting

Selective laser melting of an advanced Al-Al2O3 nanocomposite

Particulate-reinforced Al-based metal matrix composites fabricated by selective laser melting: A comprehension review

Laser ablation behavior and mechanism of Cf/C–SiC composites under different laser energy densities

The Influence of Selected Laser Engraving Parameters on Surface Conditions of Hybrid Metal Matrix Composites

Comparative study on machinability and surface integrity of γ-TiAl alloy in laser assisted milling

Characterization and Defect Analysis of Machined Regions in Al-SiC Metal Matrix Composites Using an Abrasive Water Jet Machining Process

Characteristics of hole formation during laser drilling of SiC reinforced aluminium metal matrix composites

System Design For Laser Assisted Milling Of Complex Parts

Study on the processing performance of 60% SiCp/Al composite materials assisted by longitudinal and torsional ultrasonic vibration milling

Selective Laser Melting of Al-Based Matrix Composites with Al2O3 Reinforcement: Features and Advantages

Improved direct laser assisted machining of Al 7075-T6 and Ti-6Al-4V using cubic zirconia tool