Abstract:Laser-based powder bed fusion (LPBF) is a widely utilized technique for additive manufacturing (AM) of metal components. The size of LPBF-produced parts is restricted by machine dimensions. Welding emerges as a feasible solution for connecting smaller parts generated via PBF. Nevertheless, the weldability of PBF parts differs from conventional ones due to the unique thermal history of PBF components. This paper investigated the weldability of stainless steel 316L and tensile behavior of welded samples, comparing samples produced through LPBF and the conventional wrought method. Tensile testing, grain size analysis, microhardness test, and assessment of secondary dendrite arm spacing were conducted on every welded combination of materials (AM-AM, wrought-wrought, and AM-wrought) using gas tungsten arc welding (GTAW). The findings indicate that the wrought material demonstrates a higher maximum strength (577.5 MPa) and a lower yield strength (231.7 MPa) compared to the AM material (with a maximum strength of 548.2 MPa and a yield strength of 399.9 MPa). This difference may be attributed to the annealing process applied to the wrought material, which has not been applied on the AM material. Additionally, welded wrought samples have a significantly lower tensile strength compared to non-welded samples. The wrought samples exhibit a larger average grain size (11.14 to 31.12 ) in the heat affected zone (HAZ) compared to non-heat affected regions (8.13 ). In contrast, it is found that grain coarsening does not occur in PBF samples, which exhibit a similar grain size in the HAZ (15.04 ) vs 13.97 outside of the HAZ. Larger grain sizes within the HAZ correspond to a larger reduction in tensile strength for the wrought samples, compared to PBF samples. Similar secondary dendrite arm spacing has been observed in the weld regions of both PBF and wrought materials. Microhardness test results indicated that the AM base material has the highest microhardness and gradually decreases as transitioning to the HAZ and weld region. In summary, the PBF samples exhibit less reduction of strength and ductility after welding than wrought samples. Therefore, it is determined that additively manufactured 316L stainless steel has a higher weldability than traditionally manufactured wrought 316 stainless steel.

The Effect of Low-Power Laser on Micro-Forming of 316 Stainless Steel Additive Manufacturing Part

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

Effect of processing parameters on microstructure and tensile properties of austenitic stainless steel 304L made by directed energy deposition additive manufacturing

Effects of laser additive manufacturing on microstructure and crystallographic texture of austenitic and martensitic stainless steels

Effects of gas tungsten arc welding on the mechanical properties and microstructure of 316L stainless steel by powder bed fusion

Investigation of Fabricating Stainless Steel 304L Thin-Wall Structure Using Laser Marking-Assisted Wire Arc Additive Manufacturing Process

Effect of Interlayer Temperature on Microstructure and Properties of High-Strength Low-Alloy Steel Manufactured Using Submerged-Arc Additive Manufacturing (SAAM)

Mechanical properties and microstructural characteristics of 316L stainless steel fabricated by laser powder bed fusion and binder jetting

Investigation on Forming Process and Product Properties of Laser Wire-Feed Additive Manufacturing for High-Quality Metal Thin-Walled Parts

Microstructure, strain-rate sensitivity, work hardening, and fracture behavior of laser additive manufactured austenitic and martensitic stainless steel structures

Influence of heat treatment temperature on the microstructural, mechanical, and wear behavior of 316L stainless steel fabricated by laser powder bed additive manufacturing

Platelet-derived growth factor receptor mediates activation of ras through different signaling pathways in different cell types

The Formability and Mechanical Properties of 316L Stainless Steel Fabricated by Pulsed Arc Swing Additive Manufacturing

Evolution of microstructure and mechanical properties in 2205 duplex stainless steels during additive manufacturing and heat treatment

Study of the Microstructure and Mechanical Properties in Multilayered Structures Created by Laser-PTA Additive Manufacturing

Influences of the process parameter and thermal cycles on the quality of 308L stainless steel walls produced by additive manufacturing utilizing an arc welding source

Comparison of the microstructure, mechanical properties and distortion of stainless steel 316 L fabricated by micro and conventional laser powder bed fusion

Regulation and function of the Drosophila segmentation gene fushi tarazu

Improvement of mechanical properties through inhibition of oxidation by adding TiC particles in laser aided additive manufacturing of stainless steel 316L

Microstructure effect on sliding wear of 316L stainless steel selectively laser melted

Experimental characteristics of 316L stainless steel thin wall processed in wire-based arc additive manufacturing process