Abstract:The research investigates the metallurgical and mechanical properties of multi-layered built-up of SS316L produced through cold metal transfer-based wire arc additive manufacturing. The present study focused on varying heat input and its effect on the structural properties of built-ups. The WAAMed deposits showcase the fusion lines resembling an arc-like shape without porosity or inter-layer interfaces, and that signifies the sound and defect-free built-up fabrication. The WAAMed walls have shown a dual-phase microstructure comprising γ-austenite and δ-ferrite along with associated solidification modes. The distribution of these phases is affected by heat input variations, leading to a decline in γ-austenite concentration and a rise in δ-ferrite and micro-inclusions with higher heat inputs. Concurrently, grain size and secondary dendrite arm spacing (SDAS) escalate proportionally with increased heat input, with grain size ranging from 8.23 to 11.16 μm and SDAS from 5.68 to 8.27 μm across different heat inputs. Oxygen-based micro-inclusions also increased with an increase in heat input. Vickers microhardness assessments illustrate a decline in hardness as heat input rises. The low heat input wall exhibits an average hardness of 191.056 HV, while the high heat wall exhibits an average hardness of 171.90 HV. A 10.56% drop in hardness for a 52.88% increase in heat input is observed. Impact energy also decreased as heat input increased. For low, medium, and high heat inputs, the average impact energy from bottom to top portions of walls was 115, 97.22, and 84 J, respectively. 1.528-fold increase in heat input leading to a 1.369-fold decrease in impact energy. Reducing heat input led to significant improvements in yield strength (408.66 ± 2.21 to 361 ± 1.67 MPa) and ultimate tensile strength (630.33 ± 3.75 to 577.33 ± 1.43 MPa), corresponding to increases of approximately 12.20% and 7.56%, respectively. Conversely, percent elongation decreased from 54.26 ± 1.2 to 42.83 ± 3.9%, marking a reduction of 22.22%. Fractured specimens exhibit uniformly dispersed dimples and micro-voids, signifying ductile fracture behavior indicative of good toughness. The obtained results indicate that the lower heat input would be preferential for WAAMed built-up in the context of mechanical and microstructural properties compared to high heat input for the built-up fabrication.

Influences of the process parameter and thermal cycles on the quality of 308L stainless steel walls produced by additive manufacturing utilizing an arc welding source

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

Improving mechanical strength and isotropy for wire-arc additive manufactured 304L stainless steels via controlling arc heat input

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Effect of Process Conditions on Mechanical and Metallurgical Properties of Wire Arc Additively Manufactured 316L Stainless Steel

Effect of Induction Heat Treatment on Microstructure, Mechanical and Corrosion Properties of Stainless Steel 308L Fabricated Using Wire Arc Additive Manufacturing

Effect of processing parameters on microstructure and tensile properties of austenitic stainless steel 304L made by directed energy deposition additive manufacturing

A study on wire and arc additive manufacturing of low-carbon steel components: process stability, microstructural and mechanical properties

Pulsed directed energy deposition-arc technology for depositing stainless steel 309L: Microstructural, elements distribution, and mechanical characteristics

An experimental and numerical study on the influence of interlayer time interval in wire-arc additive manufacturing process

A study on wire arc additive manufacturing of 308L austenitic stainless steel cylindrical components: Optimisation, microstructure and mechanical properties

Performance Evaluation of Cold Metal Transfer-Based Wire Arc Additive Manufacturing of SS316L: An Effect of Weld Thermal Cycles and Heat Inputs

Influence of Auxiliary Process on Microstructure and Mechanical Properties of Wire Arc Additive Manufacturing of Thick Wall Depositions

Microstructural Evolution in a Thin Wall of 2cr13 Martensitic Stainless Steel During Wire Arc Additive Manufacturing

Experimental characteristics of 316L stainless steel thin wall processed in wire-based arc additive manufacturing process

Experimental study of shielding gas concentration on mechanical properties of stainless steel alloy parts using wire and arc additive manufacturing

A preliminary study on gas metal arc welding-based additive manufacturing of metal parts

Evaluation of thermal and geometric properties of martensitic stainless steel thin walls built by additive manufacturing cold metal transfer (CMT) processes

The Effects of Processing Parameters during the Wire Arc Additive Manufacturing of 308L Stainless Steel on the Formation of a Thin-Walled Structure

EFFECTS OF WELDING CURRENT ON THE SHAPE AND MICROSTRUCTURE FORMATION OF THIN-WALLED LOW-CARBON PARTS BUILT BY WIRE ARC ADDITIVE MANUFACTURING

Effects of arc current and travel speed on the processing of stainless steel via wire arc additive manufacturing (WAAM) process