Abstract:Mn–Cu‐based alloys possess excellent mechanical and functional properties (damping capacity and shape memory effect). This work utilizes a typical additive manufacturing technique, selective laser melting (SLM), to fabricate Mn–15 wt.%Cu alloys to explore the mechanical and functional behaviors. The results indicate that the γ–(Mn, Cu) and a small amount of γ ́–(Mn, Cu) phase were the main phase composition in the as‐SLMed Mn–15 wt.%Cu alloy, as well as twins and second‐phase precipitation particles. The microstructure shows a fine cellular γ–(Mn, Cu) dendrite with primary dendrite spacing of ∽0.9 μm in the columnar grains with a size of ∽8 μm. The martensitic transformation start temperature (MS) and phase transformation hysteresis are ∽132.6 oC and ∽5.1 oC, respectively. The existing nanoscale chemical segregations of Mn and Cu are attributed to the spinodal decomposition of γ–(Mn, Cu). A compositional modulation is observed with a wavelength of ∽20 nm and an amplitude fluctuation of Mn (55–85 wt.%) and Cu concentrations (15–45 wt.%). Finally, the as‐SLMed Mn–15 wt.%Cu alloy boasts good tensile properties (359 MPa, 268 MPa, and 3.6%), damping (internal friction of 0.032 when the strain amplitude is 9×10−4), and shape memory performances (one‐way ηow=37%–48%, and two‐way ηtw=16%–20% under the pre‐deformation strain of 2–3%). This article is protected by copyright. All rights reserved.

Effect Of Ball Milling And Spark Plasma Sintering On Microstructure And Properties Of Mn-Cu Based Damping Alloy

Effect of ball-milling parameter on mechanical and damping properties of sintered Mg-Zr alloy

Effects of Cu and Mn on Mechanical Properties and Damping Capacity of Mg-Cu-Mn Alloy

Microstructure and damping property of Mn-Cu damping alloy by induction brazing and different heat treating

Effect of ball-milling on the phase structure and hydrogen storage properties of Ti0.9Zr0.1Mn1.5 alloy

Effects of Process Parameters on Microstructure and Properties of TiC Reinforced Cu-Matrix Composites

Effect of mechanical milling on microstructure evolution and mechanical properties of Al–Zn–Mg–Cu–Si alloy fabricated via spark plasma sintering

Effects of Ball Milling Times on Microstructure and Properties of Cu matrix Composites Reinforced with Graphene Oxide Nanosheets

Mechanical milling and its influence on microstructure and electric conductivity of high mass fraction TiC / Cu composites

The Effect of Cu Addition and Milling Contaminations on the Microstructure Evolution of Ball Milled Al–Pb Alloy During Sintering

Hardness and Corrosion Behavior of CrMnFeCoNi Alloy Fabricated by Ball Milling and Spark Plasma Sintering

Microstructure Characterization of the Cu-Ti-C Composites Prepared by Mechanical Alloying and Spark Plasma Sintering

EFFECTS OF HIGH-ENERGY BALL MILLING ON THE STRUCTURE AND PROPERTY OF A MULTIPHASE Al3Ti-BASED INTERMETALLIC ALLOY

Effects of high-energy ball milling on structure and mechanical properties of L12 intermetallic compound Al67Mn8Ti25

Effect of Mn on microstructure and properties of Cu-12Al powder metallurgy alloy

Effects of Extrusion on the Mechanical Properties and Damping Capacity of Mg-1.8cu-0.5mn Alloy

Spark Plasma Sintering Cobalt Base Superalloy Strengthened by Y–Cr–O Compound Through High-Energy Milling

Effect of Y on microstructure, damping properties and mechanical properties of Cu-Al-Ni-Mn alloy

Microstructure, Phase Transformation and Mechanical Property of Ni-Co-Mn-In Alloy Prepared by Spark Plasma Sintering

The mechanical and functional behaviors of Mn–15 wt.%Cu alloy produced by selective laser melting

Microstructure of Al-20% Sn-4.5% Cu Alloy During High Energy Ball Milling and Sintering Processes