Abstract:The fatigue behavior of as-cast Mg–12%Zn–1.2%Y–0.4%Zr alloy has been investigated. The S–N curve showed that the fatigue strength at 107 cycles was 45MPa. Scanning electron microscopy observations on the surfaces of the failed and unfailed specimens (after up to 1×107 cycles) suggested that the slip bands could act as preferential sites for non-propagating fatigue crack initiation, and the I-phase could effectively retard fatigue crack propagation (FCP). The macro fracture morphology clearly indicated that the overall fracture surface was composed of three regions, i.e. a fatigue crack initiation region (Region 1), a steady crack propagation region (Region 2) and a tearing region (Region 3). High-magnification fractographs showed that only porosities can act as the crack initiation sites for all specimens. Moreover, for specimens with fatigue lifetimes lower than 2×105 cycles, the cracks mostly initiated at the subsurface or surface of the specimen. However, when the fatigue lifetime was equal to or higher than 2×105 cycles, the fatigue crack initiation sites transferred to the interior of the specimen. The maximum stress intensity factors corresponding to the transition sites between Regions 1, 2 and 3 were 2 and 4.2MPam1/2, respectively. When the maximum stress intensity factor Kmax was lower than 4.2MPam1/2, in the steady crack propagation region, due to the retarding effect of I-phase/α-Mg matrix interfaces, the fatigue cracks tended to pass the I-phase/α-Mg matrix eutectic pockets directly and propagated through the grain cells, resulting in the formation of many flat facets on the fracture surface. However, when the maximum stress intensity factor was higher than 4.2MPam1/2, in the sudden failure region, the rigid bonding of I-phase/α-Mg matrix interfaces was destroyed and the cracks preferentially propagated along the interfaces, which resulted in the fracture surface being almost completely composed of cracked I-phase/α-Mg matrix eutectic pockets. Based on microstructural observation and the fracture characteristics of the two regions, it is suggested that with an increase in crack tip driving force, the FCP mode changes from transgranular propagation to intergranular propagation.

Influence of macrozones on the fatigue cracking behavior and fracture mechanisms of rolled Ti–6Al–4V alloy

Hierarchy of the macrozone features in Ti-6Al-4V alloy inferred from massive polycrystal plasticity calculations

Deciphering the Role of Macrozones in the Microstructure Globularization and Tensile Fracture: Insights from a New Developed Marine Engineering Titanium Alloy

Deformation in Fatigue Crack Tip Plastic Zone and Its Role in Crack Propagation of Titanium Alloy with Tri-Modal Microstructure

Influences of Microstructures and Macrozones on the Stress Corrosion Cracking Sensitivity of a Near Alpha Titanium Alloy

The Micro-Mechanism of Fatigue Crack Propagation for a Forged Mg–Zn–Y–Zr Alloy in the Gigacycle Fatigue Regime

Investigation of the Influence of Macrozones in Titanium Alloys on the Propagation and Scattering of Ultrasound

The Influence of Microstructure on Dwell Sensitive Fatigue in Ti–6.5Al–3.5Mo–1.5Zr–0.3Si Alloy

Local Strain Accumulation in Fatigue Crack Propagation Process of Ti‐6Al‐4V Alloy

Fatigue Crack Growth Behavior of Beta-Annealed Ti–6Al–2Sn–4Zr–xMo (x = 2, 4 and 6) Alloys: Influence of Microstructure and Stress Ratio

Crack initiation mechanisms of micro-textured Ti60 alloys with different dwell sensitivities subjected to fatigue and dwell fatigue loading

Mechanisms of Macrozone Elimination and Grain Refinement of Near Α Ti Alloy Via the Spheroidization of the Widmannstätten Structure

Fatigue Crack Propagation Behaviors in Ti-5Al-3Mo-3V-2Zr-2Cr-1Nb-1Fe Alloy with STA and BASCA Heat Treatments

Crystallographic Micro-Mechanism of Faceted Crack Initiation in Near-Α Titanium Alloy Ti6321 under Room-Temperature Fatigue and Dwell Fatigue Loadings

Study on Fatigue Behavior and Fracture Mechanism of LMD Ti-6.5Al-3.5Mo-1.5Zr-0.3Si Alloy Based on Microstructure

The Effect of Microstructure on the Plastic Strain Localization and Fatigue Crack Initiation in Cast Mg–8Gd–3Y–0.5Zr Alloy

Microstructural Influences on the High Cycle Fatigue Life Dispersion and Damage Mechanism in a Metastable Β Titanium Alloy

Α-Lamella Orientation Dependence of Fatigue Crack Propagation in As-Forged TiB/near Α-Ti Composite

Macrostructures and Mechanical Properties in Laser Melting Deposited Titanium Alloy Plate at Different Thickness Positions

The Fatigue Behavior of I-phase Containing As-Cast Mg–Zn–Y–Zr Alloy

The effects of grain morphology and crystallographic orientation on fatigue crack initiation in a metastable titanium alloy Ti-7333