Abstract:Groove surface textures with different orientations and spacings were prepared on the Ti–6Al–4V alloy by using a laser. Fretting tests (rubbed with a Ti–6Al–4V ball) were conducted under different textures, and the coefficient of friction (COF) curves, system deformation and wear morphologies were analysed in detail. The groove orientations to the fretting direction affected the fretting wear behaviour through the following ways: (1) Fretting tests on different groove orientations resulted in different fretting loop shapes at the initial stage of fretting wear. (2) The COF curves of fretting test on perpendicular grooves and 45° grooves were similar. COF presented a sharp increase after approximately 1000 cycles under relatively low loads. The COF curves of fretting test on parallel grooves and untextured surface were similar. Only a small oscillation of COF was observed during the whole fretting tests. (3) When fretting was run in gross slip regime, the magnitude of system deformation was perpendicular grooves, no-texture samples, 45° grooves, and parallel grooves in order. The above results may have resulted from the influence of surface textures on the formation and development of wear debris. For the perpendicular grooves, high pressure was recorded in partial slip regime cracks, and peeling appeared on the convex platform of samples with the groove spacing of 80 μm, and this phenomenon promoted the formation of debris. Moreover, the perpendicular grooves prevented debris from spilling out of contact areas. For the parallel grooves, the filling mechanism of grooves was found, in which the material in the upper layer gradually squeezed the material in the lower layer toward the centre and bottom of the groove, and the parallel grooves accelerated debris from spilling out of contact areas. Therefore, groove surface textures may adjust the fretting regime of titanium alloys by changing the orientation and spacing, which could provide a new tribology design for fretting friction pairs.

Composite Fretting Behaviour Of Aluminum-Lithium Alloy Against Bearing Ball

Revealing the composite fretting-corrosion mechanisms of Ti6Al4V alloy against zirconia-toughened alumina ceramic in simulated body fluid

Fretting Fatigue Behavior and Damage Mechanism of Cast Al-Si-Cu-T6 Alloy Under Two Surface Roughness conditions

Fretting Wear and Corrosion Behaviour of an Al–ZrO2/Ni Hybrid Composite Developed by Friction Stir Processing

Fretting Wear Behavior and Damage Mechanisms of Inconel X-750 Alloy in Dry Contacts

Variable cycle fretting conditions meditated wear behavior and mechanism in a self-lubricating composite coating on TC21 titanium alloy substrate

Experimental and finite element analysis for evaluating influence of contact pressure on fretting fatigue mechanisms of A319‐T6 cast aluminum alloy

Fretting Wear Behavior and Damage Mechanisms of Inconel X-750 Alloy in Dry Contact Condition

Effect of Different Levels of Free Water in Oil on the Fretting Wear of Nickel-Aluminum Bronze Based Composites

Failure Mechanism Research on Bending Fretting Fatigue of 6061-T6 Aluminum Alloy by Experiment and Finite Element Method

Effect of groove surface texture on the fretting wear of Ti–6Al–4V alloy

Study of fretting wear mechanisms of complete contacts

Fretting Properties of Biodegradable Mg-Nd-Zn-Zr Alloy in Air and in Hank’s Solution

Experimental and numerical study on the fretting wear-fatigue interaction evolution in press-fitted axles

Effects of Fretting Wear on Rolling Contact Fatigue

The Influence of Load and Angular Displacement Amplitude on the Torsional Fretting Wear of a Ball-on-Socket Cervical Disk Model

Friction and dry sliding wear of Al–Fe–Cr quasicrystals with multi-reinforcements by laser powder bed fusion

Numerical Study on Fretting Wear of DZ125/FGH99 Tenon/Mortise Joint Structure

Ti-6Al-4V fretting wear and a quantitative indicator for fretting regime evaluation

Enhancing fretting wear behavior of Ti64 alloy: The impact of surface textures and CrN-MoS 2 -Ag composite coating

Preparation and Study on Fretting Tribological Behavior of Composite Lubrication Structure on the Titanium Alloy Surface