Abstract:Adjacent segment degenerative diseases are a major clinical concern for anterior cervical corpectomy with fusion surgery. In this study, a hybrid motion-preserving cervical prosthesis consists of two articulating joints and one porous fusion body is designed to provide motion ability and reduce the occurrence of degenerative diseases. The hybrid design is fabricated from Ti–6Al–4V (TC4) alloy using selective laser melting (SLM) technology. After carburization pretreatment, two types of bearing couple SLM-TC4 self-mating and SLM-TC4/UHMWPE were studied in terms of lubrication regime, contact mechanics and wear performance. According to the ISO 18192-1 standard, five million cycles (Mc) of in vitro spine simulator wear tests were conducted in bovine serum lubricated condition.Hamrock-Dawson minimum lubrication film thickness analysis stated that both bearing was likely under boundary lubrication only, with extensive surface asperities contact. And, the contact stress encountered during in vitro condition was not enough to cause surface fatigue failure of any bearing couple. In term of wear performance, the obtained steady state wear rates were 0.160 ± 0.004 mm3/Mc for SLM-TC4 self-mating and 8.57 ± 0.06 mm3/Mc for SLM-TC4/UHMWPE bearing couples, respectively. According to these outcomes, SLM-TC4 self-mating couple was more promising for the articulating joint bearing design.For SLM-TC4 self-mating couple, the initial wear mechanism was abrasion with potential third-body abrasion wear. As the wear cycle proceeding, the TiC cermet layer was gradually damaged and exposed the local bare metal. Under this circumstance, material loss was consisted of abrasion wear, adhesion wear, and tribo-corrosion. In comparison, the wear mechanism of SLM-TC4/UHMWPE bearing was always abrasion-adhesion of UHMWPE. The surface of UHMWPE socket was severely plowed by the hard micro bulge of the TiC layer, and material loss and plastic deformation occurred only on the UHMWPE socket. In conclusion, carburization pre-treatment causes a hard TiC cermet layer formation on the SLM-TC4, which enhance its hardness and protect underling material from corrosion damage. The thickness and quality of the TiC layer directly affect the longevity of the joint prosthesis in vivo.

The Influence of Load and Angular Displacement Amplitude on the Torsional Fretting Wear of a Ball-on-Socket Cervical Disk Model

Study on torsional fretting wear behavior of a ball-on-socket contact configuration simulating an artificial cervical disk

Comparison of wear behaviors for an artificial cervical disc under flexion/extension and axial rotation motions

The Biotribological Behaviour of an Artificial Cervical Disc Model with Ball-on-Socket Contact Type under Different Material Configurations

Insight on the Mechanical and Tribological Characteristics of Ball-on-Socket Artificial Disc under Alternate Motion of Flexion Extension–Axial Rotation and Lateral Bending–Axial Rotation

Modeling and simulation of wear for alignment mechanism of large aircraft component

Studies on the Biotribological and Biological Behavior of Thermally Oxidized Ti6Al4V for Use in Artificial Cervical Disk

Study on the Wettability and Tribological Behavior of Different Polymers As Bearing Materials for Cervical Prosthesis

Wear assessment of a Ti–6Al–4V motion-preserving porous artificial-cervical-joint fabricated by SLM after surface carburization

Effect of ellipse motion paths with different aspect ratios on friction and wear of highly crosslinked polyethylene

Could Ti6Al4V be alternative as a bearing surface articulated with polymer in artificial cervical disc

Torsional friction behavior of the contact interface between the materials of an artificial knee joint replacement

Numerical Lubrication Simulation of Metal-on-Metal Hip Joints: Ball-in-Socket Model and Ball-on-Plane Model

Finite element analysis of optimized novel additively manufactured non-articulating prostheses for cervical total disc replacement

Dynamic changes of mechanical properties induced by friction in the Archard wear model

Numerical lubrication simulation of metal-on-metal artificial hip joint replacements: ball-in-socket model and ball-on-plane model

In vitro wear study of PEEK and CFRPEEK against UHMWPE for artificial cervical disc application

Contact damage failure analyses of fretting wear behavior of the metal stem titanium alloy-bone cement interface

Strain Behavior of Malaligned Cervical Spine Implanted with Metal-on-polyethylene, Metal-on-metal, and Elastomeric Artificial Disc Prostheses – A Finite Element Analysis

Finite element model predicts the biomechanical performance of cervical disc replacement and fusion hybrid surgery with various geometry of ball-and-socket artificial disc

Fretting Wear Behavior and Damage Mechanisms of Inconel X-750 Alloy in Dry Contact Condition