Abstract:The UHMWPE wear debris has become an important reason affecting the service life and clinical reliability of the prosthesis. In order to further reveal the wear debris characteristics, three kinds of UHMWPE materials including non-crosslinked UHMWPE (UPE), Crosslinked UHMWPE (XLPE) and E-vitamin doped UHMWPE (EXPE) were taken as research objects, and the quantity, size, morphology and distribution characteristics of wear debris under reciprocating sliding and compound motion modes were systematically studied. Among them, the ball-on-disk samples were adopted under reciprocating sliding, and the real ball-on-socket contact mode of artificial cervical disc prosthesis was adopted under compound motion. The tribological experiments were performed with the frequency of 2Hz under 50,000 cycles with newborn bovine serum solution. The results showed that the dominant wear mechanism was abrasive wear accompanied by fatigue cracks under reciprocating sliding mode, while adhesive wear accompanied by a few abrasive wear under compound motion mode. Compared with the quantity of wear debris under reciprocating sliding mode, the number of UHMWPE debris under composite motion mode was reduced by 28.8%, 31.4% and 37.1% for UPE, XLPE and EXPE debris, respectively. The debris results of the three different polymers were consistent in the quantity, size range, morphology and distribution, but different in the size distribution characteristics. The largest proportion of EXPE debris size occurred in the range of less than 1μm, while the largest proportion of UPE and XLPE debris size ranges from 1-5μm under reciprocating sliding mode. When the debris size was in the range of 1–5μm under compound motion mode, it accounted for the largest proportion with a value of 55.7%, 66.7% and 74.0% for UPE, XLPE and EXPE debris, respectively. The UHMWPE debris morphology included six main types: spherical, flakes, rods, fibrillar, granular, and other types. Granular and "other types" debris were the dominant types and the sum proportion of these two types of debris for the three kinds of UHMWPE materials was all as high as 80%. Hence, the material type, pair shape, load and movement profiles may have more or less influence on the quantity, size, morphology and distribution characteristics of UHMWPE debris.

Effect of ellipse motion paths with different aspect ratios on friction and wear of highly crosslinked polyethylene

Enhanced computational modelling of UHMWPE wear in total hip joint replacements: The role of frictional work and contact pressure

The Influence of Load and Angular Displacement Amplitude on the Torsional Fretting Wear of a Ball-on-Socket Cervical Disk Model

Study on the Wettability and Tribological Behavior of Different Polymers As Bearing Materials for Cervical Prosthesis

Wear Mechanism and Wear Debris Characterization of ULWPE in Multidirectional Motion

Comparison of wear behaviors for an artificial cervical disc under flexion/extension and axial rotation motions

Anomalous Wear Behavior of UHMWPE During Sliding Against CoCrMo Under Varying Cross-Shear and Contact Pressure

Study on torsional fretting wear behavior of a ball-on-socket contact configuration simulating an artificial cervical disk

Study on wear debris characteristics of different polyethylene under reciprocating sliding and compound motion modes

Torsion Wear Behavior of PEEK-on-UHMWPE as an All-Polymer Joint Combination in Total Knee Replacement

Structural and tribological characteristics of ultra-low-wear polyethylene as artificial joint materials

Influence of Cross-Shear and Contact Pressure on Wear Mechanisms of PEEK and CFR-PEEK in Total Hip Joint Replacements

Friction and wear properties of polymer, metal, and ceramic prosthetic joint materials evaluated on a multichannel screening device

Swing-torsion composite friction behavior of CoCrMo/UHMWPE contact interface of artificial knee joint prosthesis implantation materials

Potential for adhesive wear in friction couples of UHMWPE running against oxidized zirconium, titanium nitride coatings, and cobalt-chromium alloys

Effect of load on the stick-slip phenomenon and wear behavior of EPDM

The Biotribological Behaviour of an Artificial Cervical Disc Model with Ball-on-Socket Contact Type under Different Material Configurations

Torsional friction behavior of the contact interface between the materials of an artificial knee joint replacement

Effect of friction and clearance on kinematics and contact mechanics of dual mobility hip implant

Wear behaviour of cross-linked polyethylene assessed in vitro under severe conditions

In Vitro Analysis of Wearing of Hip Joint Prostheses Composed of Different Contact Materials