Abstract:Adjacent segment degenerative diseases are a major clinical concern for anterior cervical corpectomy with fusion surgery. In this study, a hybrid motion-preserving cervical prosthesis consists of two articulating joints and one porous fusion body is designed to provide motion ability and reduce the occurrence of degenerative diseases. The hybrid design is fabricated from Ti–6Al–4V (TC4) alloy using selective laser melting (SLM) technology. After carburization pretreatment, two types of bearing couple SLM-TC4 self-mating and SLM-TC4/UHMWPE were studied in terms of lubrication regime, contact mechanics and wear performance. According to the ISO 18192-1 standard, five million cycles (Mc) of in vitro spine simulator wear tests were conducted in bovine serum lubricated condition.Hamrock-Dawson minimum lubrication film thickness analysis stated that both bearing was likely under boundary lubrication only, with extensive surface asperities contact. And, the contact stress encountered during in vitro condition was not enough to cause surface fatigue failure of any bearing couple. In term of wear performance, the obtained steady state wear rates were 0.160 ± 0.004 mm3/Mc for SLM-TC4 self-mating and 8.57 ± 0.06 mm3/Mc for SLM-TC4/UHMWPE bearing couples, respectively. According to these outcomes, SLM-TC4 self-mating couple was more promising for the articulating joint bearing design.For SLM-TC4 self-mating couple, the initial wear mechanism was abrasion with potential third-body abrasion wear. As the wear cycle proceeding, the TiC cermet layer was gradually damaged and exposed the local bare metal. Under this circumstance, material loss was consisted of abrasion wear, adhesion wear, and tribo-corrosion. In comparison, the wear mechanism of SLM-TC4/UHMWPE bearing was always abrasion-adhesion of UHMWPE. The surface of UHMWPE socket was severely plowed by the hard micro bulge of the TiC layer, and material loss and plastic deformation occurred only on the UHMWPE socket. In conclusion, carburization pre-treatment causes a hard TiC cermet layer formation on the SLM-TC4, which enhance its hardness and protect underling material from corrosion damage. The thickness and quality of the TiC layer directly affect the longevity of the joint prosthesis in vivo.

Study on the Wettability and Tribological Behavior of Different Polymers As Bearing Materials for Cervical Prosthesis

Study on the Tribological Behaviors of Different PEEK Composite Coatings for Use As Artificial Cervical Disk Materials

Tribological behavior of modified polyetheretherketone composites in sliding against stainless steel under water lubrication

Could Ti6Al4V be alternative as a bearing surface articulated with polymer in artificial cervical disc

The Biotribological Behaviour of an Artificial Cervical Disc Model with Ball-on-Socket Contact Type under Different Material Configurations

Wear studies on ZrO2-filled PEEK as coating bearing materials for artificial cervical discs of Ti6Al4V

Study on torsional fretting wear behavior of a ball-on-socket contact configuration simulating an artificial cervical disk

In vitro wear study of PEEK and CFRPEEK against UHMWPE for artificial cervical disc application

Wear assessment of a Ti–6Al–4V motion-preserving porous artificial-cervical-joint fabricated by SLM after surface carburization

Tribological properties of kaolin filled UHMWPE composites in unlubricated sliding

Structural and tribological characteristics of ultra-low-wear polyethylene as artificial joint materials

Studies on the Biotribological and Biological Behavior of Thermally Oxidized Ti6Al4V for Use in Artificial Cervical Disk

Insight into the wear particles of PEEK and CFRPEEK against UHMWPE for artificial cervical disc application: Morphology and immunoreaction

Study on Tribological Properties of CoCrMo Alloys Against Metals and Ceramics As Bearing Materials for Artificial Cervical Disc

Study on the Friction and Wear Properties of PEEK Against Cortical Bone Tissue under Different Lubricating Conditions.

Friction and wear properties of polymer, metal, and ceramic prosthetic joint materials evaluated on a multichannel screening device

Biotribological properties of UHMWPE grafted with AA under lubrication as artificial joint

Ti3C2Tx‐UHMWPE Nanocomposites—Towards an Enhanced Wear‐Resistance of Biomedical Implants

Comparison of the bio-tribological properties of UHMWPE-Chirulen® and PEEK-OPTIMA® articulating against ceramics: Implications for orthopedic implants

Tribological evaluation of thermoplastic polyurethane-based bearing materials under water lubrication: Effect of load, sliding speed, and temperature

Tribological characterization of a biocompatible thin film of UHMWPE on Ti6Al4V and the effects of PFPE as top lubricating layer