Abstract:Selective laser melting (SLM) has been widely used to manufacture customised metallic parts because it provides an integrated way to manufacture three-dimensional (3D) parts from computer-aided design models after several sub-processes. On the other hand, aluminium-based nanocomposites are widely used in the aerospace and automotive industries due to their light weight, high specific strength, excellent wear resistance, but their manufacturability and mechanical properties are not well understood when these new materials are employed in SLM. This is an important consideration because, compared with traditional manufacturing technologies, SLM offers the ability to manufacture engineering parts with very complex geometries by employing a layer-by-layer manufacturing principle. Hence, this thesis systematically studies the SLM of an advanced Al-Al2O3 nanocomposite that is synthesised using high-energy ball-milling (HEBM) process. The aim of this study is to use SLM to fabricate a nearly full dense Al-Al2O3 nanocomposite composed of 96 vol.% Al and 4 vol.% Al2O3 powder. The synthesis and characterisation of ball-milled powder is the first contribution of this study, which also investigates the influence of milling and pause duration on the fabrication of ball-milled composite powder. The second contribution of this work is the development of a 3D finite element model to predict the thermal behaviour of the first layer’s composite powder. Both the transient temperature distribution and molten pool dimensions are predicted within the laser scanning, which VI enables a more efficient selection of the process parameters (e.g. hatch spacing and scanning speed). The third contribution of this study is the optimisation of the SLM process parameters and microstructure investigation of the fabricated samples. The optimum laser energy density and scanning speed that are used to fabricate nearly full dense Al-Al2O3 nanocomposites are found to be 317.5 J/mm3 and 300 mm/s, respectively. The relative density is evaluated by quantifying the porosity on both the horizontal and vertical sections. The fabricated composite parts were observed to exhibit a very fine granular-dendrite microstructure due to the rapid cooling, while the thermal gradient at the molten pool region along the building direction was found to facilitate the formation of columnar grains. The final contribution of this study is the investigation of mechanical properties such as tensile strength, microhardness and macro and nanoscale wear behaviour. Compared to pure Al, the addition of 4 vol.% Al2O3 nanoparticulates was found to contribute to a 36.3% and 17.5% increase in the yield strength and microhardness of the composite samples, respectively. Cold working was found to contribute to a 39% increase in microhardness due to grain deformation. The pin-on-disc wear testing and atomic force microscopy (AFM) nanoscratching were performed to study the macro and nanoscale wear behaviour of the fabricated samples, respectively.

Friction and dry sliding wear of Al–Fe–Cr quasicrystals with multi-reinforcements by laser powder bed fusion

In-situ synthesis of aluminum/nano-quasicrystalline Al-Fe-Cr composite by using selective laser melting

Characterization of Aluminium Matrix Compositesreinforced by Al–Cu–Fe-Cr Quasicrystalline Particles

Microstructure and Tribological Properties of Plasma Sprayed Al–Cu–Fe Quasicrystalline Coatings after Laser Post-Treatment Processing

Metallurgical reactions and tribological properties of self-lubricating Al-WS2 composites: Laser powder bed fusion Vs. spark plasma sintering

Macro and Nanoscale Wear Behaviour of Al-Al2O3 Nanocomposites Fabricated by Selective Laser Melting

Interfacial reaction kinetics of (Al63Cu25Fe12) 99Ce1 quasicrystal reinforced 6061 aluminum matrix composites

Temperature Dependence of the Tribological Properties of Laser Re-Melted Al–Cu–Fe Quasicrystalline Plasma Sprayed Coatings

Laser additive manufacturing of Ti and Ce co-modified 2195 difficult-to-process aluminum alloy: Grain refinement, cracking suppression and enhanced mechanical properties

Preparation of B4Cp/Al Composites via Selective Laser Melting and Their Tribological Properties

Rapid Solidification and Non-equilibrium Phase Constitution in Laser Powder Bed Fusion (LPBF) of AlSi10Mg Alloy: Analysis of Nano-precipitates, Eutectic Phases, and Hardness Evolution

Laser cladded AlCuFe plus Sn quasicrystalline composite coatings

Fretting wear behavior of in-situ (TiC+TiB) reinforced Ti-based composite by laser power bed fusion: Role of friction counterparts and operating frequency

Laser powder bed fusion of in-situ amorphous oxide dispersion strengthened immiscible Cu-316 L bimetallic composite: Formation mechanism and current-carrying wear behavior

Influence of re-melting rate on the dry sliding wear characteristics of LPBFed Cu–Cr–Zr alloy

Microstructure transition and mechanical properties of friction stir processed CoCrFeMnNi high entropy alloy fabricated by laser powder bed fusion

Effect of Cr on Microstructure, Mechanical Properties, and Wear Behavior of in Situ 20 Wt.%al2o3/fe-25Al Composites

Processing defect, microstructure evolution and mechanical properties of laser powder bed fusion Al-12Si alloys

Effect of Al-Cu-Fe Quasicrystal Particles on the Reinforcement of a Polymer–Matrix Composite: From Surface to Mechanical Properties

Microstructure evolution and mechanical properties of Al-Al2O3 composites fabricated by selective laser melting

Selective laser melting of an advanced Al-Al2O3 nanocomposite