Abstract:Owing to the brittleness of the body-centered cubic (BCC) structure and lack of self-lubrication, plasma-sprayed AlCoCrFeNi high-entropy alloy (HEA) coatings undergo severe abrasive wear, resulting in high friction and wear. In this study, the substrate surface temperature was increased (800 °C) to promote the phase transition from BCC to ductile FCC during spraying. As a result, the prepared AlCoCrFeNi HEA coating contained BCC and FCC phases, exhibiting a higher adhesive strength, lower friction coefficient and wear rate at room temperature (RT)–800 °C. In addition, the elevated substrate surface temperature enabled the transition of the low-temperature stable phase α-Bi 2 O 3 to the high-temperature stable phase δ-Bi 2 O 3 . δ-Bi 2 O 3 promoted the formation of low shear strength planes owing to its low interaction parameter and defect-fluorite structure with 25 % anionic vacancies similar to that of the Magnéli phase, which facilitated friction reduction in a wide temperature range. This study confirms that δ-Bi 2 O 3 can effectively improve the anti-wear performance of the AlCoCrFeNi-Bi 2 O 3 coating at RT, 200, 600 and 800 °C. However, at 400 °C, the low melting point and soft nature of the Bi 2 O 3 weakened the mechanical strength of the coating and inhibited the construction of a solid and tough tribo-layer, resulting in a relatively high wear rate for AlCoCrFeNi-Bi 2 O 3 coating. At 800 °C specifically, under the thermal coupling effect, δ-Bi 2 O 3 migrated and aggregated on the worn surface with the oxidation product Al 2 O 3 of the AlCoCrFeNi HEA matrix, and jointly promoted the formation of a compact and smooth tribo-layer with lubricating capability, which not only effectively reduced friction but also inhibited wear.

Temperature Dependence of the Tribological Properties of Laser Re-Melted Al–Cu–Fe Quasicrystalline Plasma Sprayed Coatings

Microstructure and Tribological Properties of Plasma Sprayed Al–Cu–Fe Quasicrystalline Coatings after Laser Post-Treatment Processing

Effect of the high temperature phase transition on the tribological behavior of atmospheric plasma sprayed AlCoCrFeNi-Bi 2 O 3 coating

Effect of the Laser Cladding Parameters on Microstructure and Elevated Temperature Wear of FeCrNiTiZr Coatings

Effects of laser remelting on microstructure and tribological properties of plasma–sprayed Fe45Mn35Co10Cr10 high–entropy alloy coating

Microstructure and High-Temperature Tribological Properties of Laser-Cladded WC10Co4Cr–xTi2AlC Coatings

Tribological Behavior of Plasma Sprayed Al–Cu–Fe + Sn Quasicrystalline Composite Coatings

Friction and dry sliding wear of Al–Fe–Cr quasicrystals with multi-reinforcements by laser powder bed fusion

Friction and wear properties of plasma-sprayed Cr2O3–BaCrO4 coating at elevated temperatures

Effect of Temperature and Load on Tribological Behavior in Laser-Cladded FeCrSiNiCoC Coatings

High-temperature tribological behavior of thermally-treated supersonic plasma sprayed Cr3C2-NiCr coatings

Microstructure and tribological behaviors of laser cladded CuAlMnTi–xTiC composite coatings at elevated temperature

High-Temperature Wear Behavior and Mechanisms of Self-Healing NiCrAlY-Cr3C2-Ti2SnC Coating Prepared by Atmospheric Plasma Spraying

Effect of Heat Treatment on Microstructure and Wear Behavior of Laser Clad FeCoCrMoNi High-Entropy Alloy Coatings

Microstructure, thermostability and tribological behavior of composite CoCrFeNiTix high-entropy alloy coatings fabricated by laser cladding

Effects of WC mass fraction on microstructure and tribological behavior of plasma sprayed FeMnCoCr–WC coatings

High temperature tribological behaviors and wear mechanisms of NiAl-MoO3/CuO composite coatings

Microstructure and Wear Behaviors of Plasma-Sprayed MoAlB Ceramic Coating

High temperature tribological behavior of atmospheric plasma-sprayed CoCrFeNiW0.3 + 5 at% C high-entropy alloy coating

The Analysis of the Friction and Wear Mechanisms of Plasma-Sprayed Ceramic Coatings at 450 °C

Influence of Heat Treatment on the Microstructure and Wear Properties of Arc-Sprayed FeCrAl/Al Coating