Abstract:Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, Ahead of Print. Wear is a significant cause of material loss, contributing to surface degradation of crucial components, notably within engineering sectors. This article is dedicated to enhancing tribological properties through the implementation of Al2O3-based ceramic coatings, specifically targeting situations where reciprocating sliding wear predominates. This study introduces lanthanum oxide (La2O3), a rare earth oxide, as a reinforcing material in Al2O3 coatings in varying weight percentages of 1.2%, 1.6%, and 1.8% respectively along with 3% hexagonal boron nitride (h-BN). The coatings were developed by the high-velocity oxy-fuel (HVOF) surface modification technique, with SS304 serving as the substrate. The porosity, hardness, and chemical composition of the developed coatings were examined. Additionally, reciprocating tribological testing of the coatings was conducted at two loads (5 N and 15 N) under dry sliding conditions. Results indicated that coating containing 95.4% Al2O3–3% h-BN–1.6% La2O3 reduced the porosity up to 50% and improved hardness by 46% compared to the 97% Al2O3–3% h-BN coating. The formation of the α-Al2O3 phase leads to an increase in coating hardness and a reduction in porosity. Notably, the coating comprising 97% Al2O3–3% h-BN exhibited the lowest coefficient of friction among all developed coatings under both loads. Furthermore, an increase in load led to a decrease in the coefficient of friction for all developed coatings. Furthermore, the addition of La2O3 (1.6 wt%) to the coating with 3 wt% h-BN exhibited the lowest wear at both loads. The findings also revealed increased wear at high loads for all developed coatings. SEM, EDS, and XRD analysis of the worn surfaces revealed the contribution of h-BN and La2O3 in enhancing friction behavior through the formation of oxides such as α-Al2O3, B2O3, Al8B2O15, and Al11La0.497O17, along with alterations in wear mechanism and the size of wear debris. The composite coatings developed in this study shall be helpful in advanced engineering applications.

Effect Of Surface Roughness And Wear In Lubricated Of Self-Mated Alumina On Friction Reciprocating Sliding Contact

Effect of surface polishing on the tribological performance of hard coatings under lubricated three-body abrasive conditions

Wear behaviour of ceramic coating (Al2O3-40%TiO2) in dry condition for automotive applications

Tribological behaviour of hypereutectic Al-Si automotive cylinder liner material under dry sliding wear condition in severe wear regime

The Exposure Height of Silicon Particle with Round Edges Effect on the Tribological Property of Al-Si Alloy Cylinder Liner

Frictional Characteristic Curves of Ground Surfaces in Lubricated Sliding

Effect of surface roughness on sliding friction in lubricated contacts-reciprocal experiment study

Characterisation Of Tribological Behaviour Of Silicon And Ceramic Coatings Under Repeated Sliding At Micro-Scale

Tribological Properties of Al2O3/Graphite-Al2O3 Laminated Composites under Water Lubrication Conditions

Synergism of h-BN and La2O3 in improving the tribological performance of Al2O3 coatings

The Role of Products of Tribochemical Reactions on the Friction and Wear Properties of Alumina/silicon Carbide Couple Sliding in HFC-134a Gas

Mechanisms of abrasive wear in lubricated contacts

Comparative Study on the tribological performance and wear behaviour of hypereutectic Al–Si cylinder liner surfaces textured using micro-drilling and mechanical indentation-based approaches

Effects of Surface Roughness on Sliding Friction in Lubricated-Point Contacts: Experimental and Numerical Studies

Efficiency of surface texturing in the reducing of wear for tests starting with initial point contact

Tribological Behavior of Various Plasma-Sprayed Ceramic Coatings

Influence of Counter Surface Roughness and Lay on the Tribological Behaviour of Self-Lubricating Bearing Materials in Dry Sliding Conditions at High Contact Pressures

Tribological mechanisms of slurry abrasive wear

Analysis and Evaluation of the Synergistic Effect of Ceramic Materials and Surface Texture on Anti-Abrasive Particle Wear under Rolling Conditions

Wear and surface degradation of commercial ZTA femoral heads under boundary lubrication conditions

Experimental research on the frictional performance of real laser-textured cylinder liner under different lubrication conditions