Abstract:In vessel retention (IVR) is one of the key severe accident mitigation strategies to maintain reactor pressure vessel (RPV) integrity. IVR designs utilize the reactor pressure vessel lower head to contain molten fuel and rely on external reactor vessel cooling (ERVC) to remove decay heat. The capacity of ERVC is limited by the critical heat flux (CHF) of flow boiling on the outside of the reactor vessel surface. Therefore, the determination of critical heat flux (CHF) is crucial to predict whether the adoption of IVR would be successful in mitigating severe accidents. In 1999, Celeta et.al proposed a superheated layer vapor replenishment model. In this model they postulated that CHF would occur when the superheated layer was occupied by the vapor blanket coming into contact with the heated wall and they successfully predicted the critical heat flux in subcooled water flow boiling under high mass flux, high liquid subcooling and low/medium pressure conditions. To evaluate the practicability of this model in predicting CHF under IVR conditions, CHF experiments were performed under natural circulation conditions on the experiment facility "Test of External Vessel Surface with Enhanced Cooling" (TESEC). Experiments are conducted in a 30 mm wide, 61mm high rectangular flow channel with a 200 mm long heated surface along the flow direction. Two quartz windows are installed at the sidewalls of the flow channel for visualization. In order to simulate various positions of the reactor lower head, experiments at different inclination angles of the test section were conducted. The high speed visualization data at CHF point at various inclination angles were processed and analyzed by a MATLAB code developed by the author. The vapor blanket thickness at various inclination angles was measured from the visualization data and was also predicted by the Celeta model. By using geometry data from high speed images, CHF values were calculated by Celeta model and compared with the experimental results at various inclination angles. Limitations of the Celeta model in adaptation of predicting CHF under IVR conditions were further discussed.

Cfd Application To Subcooled Boiling Analyses On The First Wall Of Wccb Blanket For Cfetr

Neutronics Comparison Analysis of the Water Cooled Ceramics Breeding Blanket for CFETR

An Approach to Increase the Fusion Tritium Breeding Ratio Using Temperature Field Balance Based on Water-Cooled Ceramic Blanket

Studies on Flibe Blanket Designs in Helical Reactor FFHR

Development of neutronic-thermal hydraulic-mechanic-coupled platform for WCCB blanket design for CFETR

CFD study on flow-boiling characteristics and predicting critical heat flux under natural circulation conditions of IVR-ERVC

Thermohydraulic and thermal fatigue characteristics of W/Cu flat-type microchannel mock-up for CFETR divertor

Study of W/Cu Flat-Type Mock-Ups with Novel Hypervapotron Cooling Structure for CFETR Divertor

CFD study of two-phase cross flow and heat transfer in sub-channels of pressurized water reactor fuel assemblies

The hydrodynamic characteristics of embattlement shaped water wall of a 350 mw supercritical circulating fluidized bed boiler

Multiphase CFD-based critical heat flux predictions for single-element heaters at CANDU reactor conditions

Flow boiling heat transfer and pressure fluctuation characteristics in a divergent channel with inclined downward-facing heater

Numerical simulation of the temperature field in the ITER Chinese helium cooled solid breeder test blanket module

Prediction Of subcooled water flow boiling critical heat flux (CHF) at low pressure

Heat Flux Distribution on Circulating Fluidized Bed Boiler Water Wall

Investigation on the Tritium Self-Sufficiency and Neutron Shielding Based on a Water-Cooled Blanket for CFETR at 1.5 GW

Thermal Hydraulic Review of Light Water Reactor Based on Subchannel Code CTF

Heat transfer characteristic of water wall and partition wall in a 600 MW CFB boiler

Tritium Transport Modeling and Analysis for HCCB Blanket of CFETR

Numerical Investigation of Flow Boiling Characteristics in Narrow Rectangular Channels Using Two-Fluid Eulerian Cfd Model Covering a Wide Range of Pressures

OpenFOAM CFD simulation of critical heat flux in vertical pipe under typically PWR conditions