Abstract:A site-specific xenon plasma focused ion beam preparation technique for microcantilever samples (1-20 µm width and 1:10 aspect ratio) is presented. The novelty of the methodology is the use of a chunk lift-out onto a clean silicon wafer to facilitate easy access of a low-cost probe type indenter which provides bending force measurement. The lift-out method allows sufficient room for the indenter and a line of sight for the electron beam to enable displacement measurement. An electroplated nanotwinned copper (NTC) was cut to a 3 × 3 × 25 µm microbeam and in situ mechanically tested using the developed technique. It demonstrated measured values of Youngs modulus of 78.7 ± 11 GPa and flow stress of 0.80 ± 0.05 GPa, which is within the ranges reported in the literature. LAY DESCRIPTION: In this paper a site specific method is present for making particularly small mechanical tests samples, of the order of 100th the size of a human hair. These small samples can then be used to determine the mechanical properties of the bulk material. Copper with a nano twinned grain structure is used as a test medium. Ion milling was used to cut the sample to shape and a micro probe was used for mechanical testing. Ion milling can cut away very small volumes of material as it accelerates ions at the surface of the sample, atomically machining the sample. Micro probes are a cost-effective small-scale load measurement devices, however, they require a large area for accessing the sample. The indenter requirements are a problem when making you samples with ion milling as ion millers are best at making small cuts. Our aim was to design a cutting strategy which reduces the amount of cutting required while allowing samples to be fabricated anywhere on the sample. We used a chunk lift out technique to remove a piece of material which is then welded to a wafer of silicon this gives sufficient space around the sample for ion milling and testing. The additional space allowed easy access for the probe. A 3 × 3 × 10 µm micro cantilever beam was cut out from copper, this beam was then bent. The force from bending and distance bent was measured and converted into Youngs modulus which is a measure of flexibility. The modulus value measured was comparable to the values reported in other papers.

Quantitative Metrology Study of Cu/Sio2 Interconnect Structures Using Fluorescence X-Ray Microscopy

In situ nanomechanical measurement of Cu nanowires

Understanding the Impact of Surface Engineering, Structure, and Design on Electromigration Through Monte Carlo Simulation and In‐Situ SEM Studies

Measuring residual stresses in individual on-chip interconnects using synchrotron nanodiffraction

Quantitative Measurement of Submicrometre Electrical Conductivity

In Situ Nanoscale Deformation Studies on Micro Copper Wires Using Atomic Force Microscopy

Experimental and Numerical Studies of Stress Migration in Cu Interconnects Embedded in Different Dielectrics

Methodology for Measurement of Submicron Metallic Wire's Local Electrical Conductivity by Applying Four-points AFM Probe Technique

Laboratory High-Contrast X-ray Microscopy of Copper Nanostructures Enabled by a Liquid-Metal-Jet X-ray Source

Unravelling nanometallurgy with in situ transmission electron microscopy: A case-study with copper nanowires

In Situ Investigation of Microstructural Evolution and Intermetallic Compounds Formation at Liquid Al/Solid Cu Interface by Synchrotron X-ray Radiography

Noncontact electrical metrology of Cu/low-k interconnect for semiconductor production wafers

Laboratory X-ray Microscopy of 3D Nanostructures in the Hard X-ray Regime Enabled by a Combination of Multilayer X-ray Optics

Quantitative Chemically-Specific Coherent Diffractive Imaging of Buried Interfaces using a Tabletop EUV Nanoscope

MEMS Device for Quantitative in Situ Mechanical Testing in Electron Microscope

In situ electron microscopy four-point electromechanical characterization of freestanding metallic and semiconducting nanowires

In Situ Measurement of Stress Evolution in Sn-based Solder Joint under Electromigration Based on X-ray Diffraction Technique

A Microstructure-Based Study on Electromigration in Cu Interconnects

Investigations on the Thermal Conductivity of Micro-Scale Cu-Sn Intermetallic Compounds Using Femtosecond Laser Time-Domain Thermoreflectance System

In situ measurements on individual thin carbon nanotubes using nanomanipulators inside a scanning electron microscope

Focused ion beam preparation of microbeams for in situ mechanical analysis of electroplated nanotwinned copper with probe type indenters