Abstract:In response to the problems of low strength and high permeability of coal materials in the current physical simu-lation test of coal mine gas dynamics,a set of experimental research methods for optimizing the molding conditions of hot-pressed briquette.Firstly,a hot-pressed briquette test system was independently established and the advantages and future improvement directions of the test system were summarized.At the same time,based on the Horsfield dense stacking the-ory,the optimal preparation plan for coal briquette materials was formulated.Finally,a molding condition optimization method was developed that combines the Markov distance measurement method and the golden section method.To verify the effectiveness of the experimental method,the secondary carbonization experiments of briquette were conducted under different molding pressure conditions by controlling the molding temperature to 311.8℃,heating rate to 5℃/min,and holding time to 5.3 h.The response characteristics of the microstructure,physical and mechanical properties,and permeab-ility characteristics of the hot-pressed briquette under different molding pressure conditions were studied.The results show that with the increase of molding pressure,the total porosity gradually decreases,and the uniaxial compressive strength shows a trend of first increasing and then decreasing.The main forms of failure are block spalling and longitudinal frac-ture.The initial permeability shows a trend of first decreasing and then increasing,while the minimum permeability shows a trend of first decreasing,then increasing and then decreasing.Using the specific values of each molding condition as the test points,and the key parameters of hot-pressed coal and raw coal as the evaluation parameters,a sample matrix was constructed to calculate the Mahalanobis distance between hot-pressed briquette and raw coal under each molding condi-tion,and then optimize the experimental interval using the golden section method.The optimized final molding pressure is 80 MPa.Under these molding conditions,the density,uniaxial compressive strength,and initial permeability of the hot-pressed briquette produced are 1.137 g/cm3,12.21 MPa,and 1.32×10-15 m2,respectively.They are highly similar to the 1.132 g/cm3,12.83 MPa,and 1.08×10-15 m2 of the raw coal,achieving the goal of improving the strength of the briquette and reducing the permeability of the briquette.

Investigation Of Coal Tar Pitch Binder For The Production Of Formed Coal Briquettes For Corex From High Volatile Coal Powder

Coal Tar Pitch and Molasses Blended Binder for Production of Formed Coal Briquettes from High Volatile Coal

Xylene Activation of Coal Tar Pitch Binding Characteristics for Production of Metallurgical Quality Briquettes from Coke Breeze

Bonding Mechanism of Binder and Low-Rank Coal During Carbonization

Effect of binder composition on the preparation of formed coke with low-rank coal

High Strength Clean Briquettes Production from Long‐flame Coal Fines by Using Polyvinyl Alcohol and Coal Slime As Binders

Study on preparation of high strength formed coke

Preparation of micro-porous monolithic activated carbon from anthracite coal using coal tar pitch as binder

Preparation of formed coke product as a coke substitute using a solid waste fuel: Trimethylbenzene improvement on coal tar pitch

Thermal extraction of coal and derivatives to prepare hot-pressed coal briquette for COREX application

Preparation of high-performance binderless carbon material with coal-tar pitch as raw material

Study on Briquette for Gasification and Boiler by Ueing Kailuan, Liujiang, Datong Fine Coal

Enhancement of coal tar pitch carbonization with biochar: A metallurgical formed biocoke product produced by waste coke breeze and bamboo powder

Effect of molecular carbon structures on the evolution of the pores and strength of lignite briquette coal with different heating rates

EFFECT OF COAL PITCH AND MIXING RATIO OF COKE GRAIN ON PROPERTIES OF GRANULAR CO KE REINFORCED PITCH- BASED CARBON COMPOSITES

Effect of Binders on the Crushing Strength of Ferro-Coke

Study of an Organic Binder of Cold-Bonded Briquettes with Two Different Iron Bearing Materials

Experimental method for optimizing the molding conditions of hot-pressed briquette

Hyper-coal As Binder for Coking: —macroscopic Caking Property, Microstructure Basis and Extraction Temperature Optimization Index

Co-combustion, Co-Densification, and Pollutant Emission Characteristics of Charcoal-Based Briquettes Prepared Using Bio-Tar As a Binder

Physical and Chemical Characteristics of Coal-binder Interface and Carbon Microstructure near Interface