Abstract:An in-situ compatibilized starch (St) and polyacrylonitrile (PAN) composite spinning solution was designed by preparing starch-graft-polyacrylonitrile (St-g-PAN) through graft copolymerizing acrylonitrile from soluble starch and using ammonium cerium nitrate (CAN) as initiator. As dimethyl sulfoxide (DMSO) was used as the solvent, St/St-g-PAN/PAN/DMSO spinning solution was prepared and St/St-g-PAN/PAN composite fibers were obtained by dry-wet spinning technique. The effects of air gap, coagulation bath, hot drawing and stretching, and thermal-setting process were studied in detail. Fourier transform infrared spectroscopy (FT-IR), solid state nuclear magnetic resonance (13C NMR), thermogravimetric analysis (TGA), X-ray diffraction analysis (XRD), and scanning electron microscopy (SEM) were used to characterize the structure and morphology of the copolymer and the fibers. Single fiber strength tester and sonic orientation instrument were performed to measure the fiber mechanical properties and orientation degrees. The results showed that as the grafting ratio ~150.0% and the reacting mixture containing St ~9.8%, St-g-PAN ~81.6%, and homo-PAN ~8.6% in DMSO solution with 6.0 wt% in concentration were used, the spinning parameters such as air gap ~35 mm, coagulation bath concentration ~70%, temperature ~25 °C, and positive stretching ~48%, hot drawing and stretching 6 times at 80 °C, thermal-setting at 90 °C for 3 h under constant length mode were met, composite fibers with breaking strength 3.41 cN·dtex−1, breaking elongation 14.41%, sonic orientation factor 0.625, moisture recovery ratio 10.53% under standard condition (1 atm, 22 °C, and relative humidity 65%), and boiling water shrinkage ratio 9.60% were obtained. The as prepared composite fiber was better than common viscose fiber 2.11 cN·dtex−1 and cotton fiber ~3.24 cN·dtex−1 and expected to be used in the fields of medical gauze, bandage, protective clothing, et al. besides of common textiles. The in-situ compatibilization method can be applied in preparation of other composite polymer materials.

Study On The Spinnability In Gel Spinning Of Pan Precursor Fiber

Effects of Moisture Content and Heat Treatment on the Viscoelasticity and Gelation of Polyacrylonitrile/Dimethylsulfoxide Solutions

STUDIES ON ONE-STEP ELECTROSPINNING FOR PREPARING CROSSLINKED GELATIN FIBERS

Microstructural Evolution during Dry-Jet Wet Spinning Postprocessing from Coagulation Bath Fiber to High-Performance Polyacrylonitrile Precursor Fiber

Comprehensive research on the correlation between microstructure and mechanical properties of polyacrylonitrile‐based precursor fibers prepared by wet‐spinning

Optimization design and properties of PVA/GEL nanofibers

Study on BC/PAN Blending Nanofibers by Elecrtospinning

Non-Coagulant Spinning of High-Strength Fibers from Homоpolymer Polyacrylonitrile Synthesized via Anionic Polymerisation

Enhanced Mechanical Performance of Electrospun Graphene/Polyacrylonitrile (PAN) Composite Microfibrous Yarns Via Post-Processing

Study on the Formation Process of Polyacrylonitrile As‐spun Fiber

In-situ compatibilized starch/polyacylonitrile composite fiber fabricated via dry-wet spinning technique

Effect of Coagulation Conditions on the Radial Moduli of Polyacrylonitrile Nascent Fibers

PREPARATION OF POROUS POLYACRYLONITRILE ULTRATHIN FIBERS BY ELECTROSPINNING WITH NONSOLVENT INDUCED PHASE SEPARATION

Effect of Coagulation Bath Concentration on the Structure and Properties of Polyacrylonitrile As-Spun Fibers During Wet-Spinning

Study on the Mass Transfer Process in Pan Wet-Spinning

Relationship Between Technics and Properties During PAN Precursors Formation Process

The effects of electrospinning parameters on coaxial polyacrylonitrile/polyurethane nanofibers: Morphology and water vapour transmission rate

A Comprehensive Study on the Rheological Properties of Collagen/PVA Spinning Solutions from Acetic Acid Solvent

Preparation and Properties of Poly (vinyl Alcohol) Nanofibers by Electrospinning

Effect of receiver plate temperature and magnetic lens on the performance of electrospun PAN

Melt-Spinning of an Intrinsically Flame-Retardant Polyacrylonitrile Copolymer