Abstract:Municipal solid waste incineration (MSWI) fly ash has been classified as hazardous waste and needs treatment in an environmentally safe manner. Mechanochemical (MC) treatment is such a detoxification method, since it destroys dioxins and solidifies heavy metals. Milling, however, also introduces supplemental metals (Fe, Ni, Cr, Mn…), following wear of both steel balls and housing. Milling moreover reduces the particle size of fly ash and disperses catalytic metal, potentially rising the reactivity of fly ash to form and destroy ‘dioxins’, i.e. polychlorinated dibenzo- p -dioxins and dibenzofurans (PCDD + PCDF or PCDD/F). To test this issue, model fly ash (MFA) samples were composed by mixing of silica, sodium chloride, and activated carbon, and doped with CuCl 2 . Then, these samples were first finely milled without any additives for 0 h (original sample), 1 h and 8 h, and the effect of milling time (and hence particle size) was investigated on the formation of polycyclic aromatic hydrocarbons (PAHs), and of polychlorinated phenols (CP), benzenes (CBz), biphenyls (PCB) and dioxins (PCDD + PCDF) during de novo tests at 300 °C for 1 h, thus simulating the conditions prevailing in the post-combustion zone of an incinerator, where dioxins are formed and destroyed. These compounds are all characterized by their rate of generation (ng/g MFA) and their signature, i.e. internal distribution over congeners as a means of gathering mechanistic indications. PAH and CBz total yield did not decrease in MC treated MFA with milling time, while total pentachlorophenol (PeCP), PCB and PCDD/F yield decreased up to 86, 94 and 97%, respectively. International Toxic Equivalents (I-TEQ) concentration decreased more than 90%, while degree of chlorination varied inconsistently for PCB and PCDD/F, and average congener patterns of PCDD/F do not vary considerably with milling time for both gas and solid phase.

Effect Of Ball Milling Time On Pcdd/Fs Formation

Long-term Ball Milling and Hot Pressing of In-Situ Nanoscale Tungsten Carbides Reinforced Copper Composite and Its Characterization

Effect of Milling Material on Characteristics and Reactivity of Mechanically Treated Fly Ash to Produce PCDD/F

The Degradation of PCDD/Fs in Fly Ash Using Dielectric Barrier Discharge in a Lab-Scale Reactor

Mechanochemical Treatment of Fly Ash and De Novo Testing of Milled Fly Ash

PCDD/F Formation in Milled Fly Ash: Metal Chloride Catalysis

De novo formation of dioxins from milled model fly ash

Mechanochemical Degradation of PCDD/Fs in Fly Ash Within Different Milling Systems.

Decomposition of PCDD/Fs by mechanochemical means with calcium-based additives

Experimental Study on Low Temperature Thermal Treatment of Polychlorinated Dibenzo-P-dioxins and Dibenzofurans (pcdd/fs) in Fly Ash

Experimental Study of PCDDs/Fs Formation from Fluorene Catalyzed by Model Fly Ash

Formation of Polychlorinated Dibenzo-P-Dioxins and Dibenzofurans on Chlorobenzene and Fly Ash

Effects of Chlorine Speciation and Characteristic of Fly Ash on the De Novo Formation of Polychlorinated Dibenzo-P-Dioxins and Dibenzofurans

Dioxins Degradation and Reformation During Mechanochemical Treatment.

Characterization of Dioxins and Heavy Metals in Chelated Fly Ash

EXPERIMENTAL STUDY ON LOW TEMPERATURE THERMAL TREATMENT OF PCDD/Fs IN FLY ASH

Dioxins Reformation and Destruction in Secondary Copper Smelting Fly Ash under Ball Milling

Effect of Zn, Cd compounds on formation of dioxins in model fly ash

De Novo Formation of PCDD/F During Sintering: Effect of Temperature, Granule Size and Oxygen Content

Mechanical Treatment of MSWI fly Ash: A Way Forward to Inhibit PCB Reformation

Decomposition and reformation pathways of PCDD/Fs during thermal treatment of municipal solid waste incineration fly ash.