Abstract:Municipal solid waste incineration (MSWI) fly ash has been classified as hazardous waste and needs treatment in an environmentally safe manner. Mechanochemical (MC) treatment is such a detoxification method, since it destroys dioxins and solidifies heavy metals. Milling, however, also introduces supplemental metals (Fe, Ni, Cr, Mn…), following wear of both steel balls and housing. Milling moreover reduces the particle size of fly ash and disperses catalytic metal, potentially rising the reactivity of fly ash to form and destroy ‘dioxins’, i.e. polychlorinated dibenzo- p -dioxins and dibenzofurans (PCDD + PCDF or PCDD/F). To test this issue, model fly ash (MFA) samples were composed by mixing of silica, sodium chloride, and activated carbon, and doped with CuCl 2 . Then, these samples were first finely milled without any additives for 0 h (original sample), 1 h and 8 h, and the effect of milling time (and hence particle size) was investigated on the formation of polycyclic aromatic hydrocarbons (PAHs), and of polychlorinated phenols (CP), benzenes (CBz), biphenyls (PCB) and dioxins (PCDD + PCDF) during de novo tests at 300 °C for 1 h, thus simulating the conditions prevailing in the post-combustion zone of an incinerator, where dioxins are formed and destroyed. These compounds are all characterized by their rate of generation (ng/g MFA) and their signature, i.e. internal distribution over congeners as a means of gathering mechanistic indications. PAH and CBz total yield did not decrease in MC treated MFA with milling time, while total pentachlorophenol (PeCP), PCB and PCDD/F yield decreased up to 86, 94 and 97%, respectively. International Toxic Equivalents (I-TEQ) concentration decreased more than 90%, while degree of chlorination varied inconsistently for PCB and PCDD/F, and average congener patterns of PCDD/F do not vary considerably with milling time for both gas and solid phase.

Decomposition of PCDD/Fs by mechanochemical means with calcium-based additives

The Degradation of PCDD/Fs in Fly Ash Using Dielectric Barrier Discharge in a Lab-Scale Reactor

Mechanochemical Degradation of PCDD/Fs in Fly Ash Within Different Milling Systems.

Dioxins Degradation and Reformation During Mechanochemical Treatment.

Degradation of PCDD/Fs by Mechanochemical Treatment of Fly Ash from Medical Waste Incineration.

Degradation of Dioxins in Chelated Municipal Solid Waste Incineration Fly Ash by Low-Temperature Pyrolysis

Mechanochemical Treatment of Fly Ash and De Novo Testing of Milled Fly Ash

PCDD/F Formation in Milled Fly Ash: Metal Chloride Catalysis

Mechanochemical Degradation of Ocdd/Ocdf in Fly Ash from Medical Waste Incinerators

[Influence of Additives on Decomposition of PCDD/Fs During MSWI Fly Ash Melting Process].

Degradation of PCDD/Fs in MSWI Fly Ash Using a Microwave-Assisted Hydrothermal Process

Improving Microwave-Assisted Hydrothermal Degradation of PCDD/Fs in Fly Ash with Added Na2HPO4 and Water-Washing Pretreatment.

Evolution of PCDD/F-signatures During Mechanochemical Degradation in Municipal Solid Waste Incineration Filter Ash.

Decomposition and reformation pathways of PCDD/Fs during thermal treatment of municipal solid waste incineration fly ash.

Comparative Analyses of Catalytic Degradation of PCDD/Fs in the Laboratory Vs. Industrial Conditions

Effect of Milling Material on Characteristics and Reactivity of Mechanically Treated Fly Ash to Produce PCDD/F

Comparative analyses of catalytic degradation of PCDD/Fs in the laboratory vs. industrial conditions.

Hydrothermal Oxidation Degradation of Dioxins in Fly Ash with Water-Washing and Added Ce-Mn Catalyst

De novo formation of dioxins from milled model fly ash

Degradation of PCDD/Fs in Fly Ash by Vortex-shaped Gliding Arc Plasma

Effect Of Ball Milling Time On Pcdd/Fs Formation