Abstract:Municipal solid waste incineration (MSWI) fly ash has been classified as hazardous waste and needs treatment in an environmentally safe manner. Mechanochemical (MC) treatment is such a detoxification method, since it destroys dioxins and solidifies heavy metals. Milling, however, also introduces supplemental metals (Fe, Ni, Cr, Mn…), following wear of both steel balls and housing. Milling moreover reduces the particle size of fly ash and disperses catalytic metal, potentially rising the reactivity of fly ash to form and destroy ‘dioxins’, i.e. polychlorinated dibenzo- p -dioxins and dibenzofurans (PCDD + PCDF or PCDD/F). To test this issue, model fly ash (MFA) samples were composed by mixing of silica, sodium chloride, and activated carbon, and doped with CuCl 2 . Then, these samples were first finely milled without any additives for 0 h (original sample), 1 h and 8 h, and the effect of milling time (and hence particle size) was investigated on the formation of polycyclic aromatic hydrocarbons (PAHs), and of polychlorinated phenols (CP), benzenes (CBz), biphenyls (PCB) and dioxins (PCDD + PCDF) during de novo tests at 300 °C for 1 h, thus simulating the conditions prevailing in the post-combustion zone of an incinerator, where dioxins are formed and destroyed. These compounds are all characterized by their rate of generation (ng/g MFA) and their signature, i.e. internal distribution over congeners as a means of gathering mechanistic indications. PAH and CBz total yield did not decrease in MC treated MFA with milling time, while total pentachlorophenol (PeCP), PCB and PCDD/F yield decreased up to 86, 94 and 97%, respectively. International Toxic Equivalents (I-TEQ) concentration decreased more than 90%, while degree of chlorination varied inconsistently for PCB and PCDD/F, and average congener patterns of PCDD/F do not vary considerably with milling time for both gas and solid phase.

Mechanochemical Degradation of Ocdd/Ocdf in Fly Ash from Medical Waste Incinerators

Degradation of PCDD/Fs by Mechanochemical Treatment of Fly Ash from Medical Waste Incineration.

The Degradation of PCDD/Fs in Fly Ash Using Dielectric Barrier Discharge in a Lab-Scale Reactor

Degradation of Dioxins in Chelated Municipal Solid Waste Incineration Fly Ash by Low-Temperature Pyrolysis

Mechanochemical Treatment of Fly Ash and De Novo Testing of Milled Fly Ash

Dioxins Degradation and Reformation During Mechanochemical Treatment.

Characterization of Dioxins and Heavy Metals in Chelated Fly Ash

Degradation of PCDD/Fs in MSWI Fly Ash Using a Microwave-Assisted Hydrothermal Process

Hydrothermal Decomposition of Polychlorinated Divenzo-p-dioxins and Dibenzofurans in Fly Ash of Medical Waste Incinerator

Mechanochemical Degradation of PCDD/Fs in Fly Ash Within Different Milling Systems.

De novo formation of dioxins from milled model fly ash

Experimental Study on Thermal Treatment of Dioxins in Fly Ash from Medical Waste Incinerator

Effect of supercritical water oxidation onthe PCDD/FS and heavy metals in incineration fly ash

Utilization of Mechanochemically Pretreated Municipal Solid Waste Incineration Fly Ash for Supplementary Cementitious Material

Hydrothermal degradation of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans in fly ash from municipal solid waste incineration under non-oxidative and oxidative conditions

A full-scale study on thermal degradation of polychlorinated dibenzo- p-dioxins and dibenzofurans in municipal solid waste incinerator fly ash and its secondary air pollution control in China

Low-temperature thermal treatment of dioxin in medical waste fly ash under unert atmosphere]

Degradation technologies and mechanisms of dioxins in municipal solid waste incineration fly ash: A review

Mechanical Treatment of MSWI fly Ash: A Way Forward to Inhibit PCB Reformation

Detoxifying PCDD/Fs and heavy metals in fly ash from medical waste incinerators with a DC double are plasma torch

Removal of carbon and dioxins from municipal solid waste incineration fly ash by ball milling and flotation methods