Abstract:A solid potentiometric CO 2 sensor has been developed using Li 3 PO 4 as the electrolyte, Li 2 TiO 3 /TiO 2 as the reference electrode, and Li 2 CO 3 as the sensing electrode. The Li 3 PO 4 film was deposited on Al 2 O 3 substrate by resistance heating evaporation. Two Pt electrodes with designed patterns were formed on the electrolyte film by micro fabrication technologies. The reference electrode and the sensing electrode were prepared by thick-film technology to cover part of the two Pt electrodes. Various properties were tested: sensitivity under different conditions, response and recovery properties, cross-interference performance, and stability. The values of ΔEMF/dec are 22 mV/dec, 45 mV/dec, and 78 mV/dec in accordance with the operating temperatures: 300°C, 400°C, and 500°C. At 500°C, the response time and recovery time are 30 s and 40 s, respectively, which is better than those of 400°C. When the thickness of Li 3 PO 4 film is greater than 650 nm, the EMF output of the sensor changes little with change of the film thickness. From the results, it can be concluded that the optimal working temperature for the sensor is 500°C, and the optimal thickness of Li 3 PO 4 is about 650 nm.

Structural and Properties Study of Li(3)Po(4 )thin Film Electrolyte for Potentiometric Nox Sensing

Au Thin-Film Electrodes Based Potentiometric CO 2 Sensor Using Li 3 PO 4 As Both the Reference Material and the Solid Electrolyte

Increasing the Sensitivity of an Amperometric, YSZ-based Total-Nox Sensor by Opening the Gas Diffusion Pathways in a Porous La0.8Sr0.2MnO3 Electrode

Response Characteristics of A Potentiometric Co2 Gas Sensor Based on Li3po4 Solid Electrolyte Using Au Film As the Electrodes

Prototypes of Potentiometric SO2 Gas Sensors Based on Li3PO4 Electrolyte Thin Film

Potentiometric NO2 Sensors Based on Thin Stabilized Zirconia Electrolytes and Asymmetric (La0.8Sr0.2)0.95MnO3 Electrodes

A Potentiometric So2 Gas Sensor Based On The Li3po4-Li2sio3 Solid Electrolyte Thin Film

Mixed-potential Type NO2 Sensor Prepared with CuCr2O4-CuO Composite Sensing Electrode

An Amperometric NO2 Sensor Based on La10Si5NbO27.5 Electrolyte and Nano-Structured CuO Sensing Electrode.

Solid-state Potentiometric CO 2 Sensor Combining Li 3 PO 4 with MoO 3 -Doped Li 2 CO 3 Sensing Electrode

Improved Sensing Properties of CO2Gas Sensor Based on Li3PO4-Li2SiO3Thin Film Compared with Li3PO4

Electrochemically tuning Li1+xFePO4 for high oxidation state of rich Li+ toward highly sensitive detection of nitric oxide

Solid Potentiometric ${\rm CO}_{2}$ Sensor Using ${\rm Li}_{3}{\rm PO}_{4}$ Film as the Electrolyte

An Amperometric Type NO2 Sensor Utilizing La0.7Sr0.3MnO3-δ-NiO Composite Sensing Electrode

Room-Temperature Mixed-Potential Type ppb-Level NO Sensors Based on K 2 Fe 4 O 7 Electrolyte and Ni/Fe–MOF Sensing Electrodes

Mixed-Potential-Type Gas Sensors Based on Pt/YSZ Film/LaFeO3 for Detecting NO2

Solid potentiometric CO 2 sensor using Li 3PO 4 film as the electrolyte

Enhancing the Performance of Mixed-Potential NO2 Sensors by Optimizing the Micromorphology of La0.8Sr0.2MnO3 Electrodes

Performance Improvement of NiO/YSZ Sensitive Electrode for High Temperature Electrochemical NOx Gas Sensors

Fabrication of thin film potentiometric CO2 sensors on differentiate substrate surfaces and their characteristics

Mixed-potential type NO2 sensor based on La10Si6O27 electrolyte and WO3 sensing electrode with different morphologies