Abstract:In the mixed-potential gas sensor, the electrode type, particle size, microstructural morphology, as well as the interface state between the oxide-sensitive electrode and the solid electrolyte, are the key factors for determining the magnitude of the mixed potential. NiO-based material with the addition of Y2O3-stabilized 2 O 3-stabilized ZrO2 2 (YSZ) particles is considered as one of the promising sensitive electrode materials for preparing the mixed-potential NOx x sensors due to its excellent gas sensitivity. In this paper, the preparation technology of NiO-sensitive electrodes is developed and optimized for improving NOx x (NO and NO2) 2 ) gas-sensitivity properties of the NOx x sensors. The experimental results show that the addition of YSZ can effectively improve the agglomeration morphology of NiO particles in the NOx-YSZ-based x-YSZ-based electrode material during high temperature sintering (i.e. 1200 degrees C) and enhance the bonding strength with the solid electrolyte. The sensor which was prepared by using the developed NOx-YSZ-based x-YSZ-based electrode material with the YSZ addition of 20 wt% has the most sensitive response characteristic to NO gas, and its response potential value increases with NO gas concentration. Elevating electrode sintering temperature can increase the size of NiO particles and shorten the length of the three-phase boundary (TPB) in the sensitive electrode. The average length of TPB is the longest in the sensitive electrode sintered at 1000 degrees C which corresponds to the best sensitive response to NO gas. The sensitive electrode's thickness also affects the NO response sensitivity, and the sensor with an electrode thickness of 14 mu m has the most NO response sensitivity. In addition, the NO/NO2 2 gas mixture test results indicate that the current developed sensor is more sensitive to NO2 2 gas than that of NO gas.

Enhancing the Performance of Mixed-Potential NO2 Sensors by Optimizing the Micromorphology of La0.8Sr0.2MnO3 Electrodes

Increasing the Sensitivity of an Amperometric, YSZ-based Total-Nox Sensor by Opening the Gas Diffusion Pathways in a Porous La0.8Sr0.2MnO3 Electrode

An Enhancement on Sensing Performance by Regulating the Micromorphology of La0.8sr0.2mno3 Electrode in Mixed-Potential Type No2 Sensor

Enhanced Sensing Performance of the Amperometric NO2 Sensor by Use of a Mixed Conductive Porous Layer

Enhancement of La0.8Sr0.2MnO3-based amperometric total NOX sensor via modification with Pt nanoparticles

An Amperometric Type NO2 Sensor Utilizing La0.7Sr0.3MnO3-δ-NiO Composite Sensing Electrode

Potentiometric NO2 Sensors Based on Thin Stabilized Zirconia Electrolytes and Asymmetric (La0.8Sr0.2)0.95MnO3 Electrodes

Influence of process parameters on the sensitivity of an amperometeric NO2 sensor with La0.75Sr0.25Cr0.5Mn0.5O3−δ sensing electrode prepared by the impregnation method

Mixed-potential type NO2 sensor based on La10Si6O27 electrolyte and WO3 sensing electrode with different morphologies

NO 2 sensing properties of electrode-supported sensor by tape casting and co-firing method

Performance Improvement of NiO/YSZ Sensitive Electrode for High Temperature Electrochemical NOx Gas Sensors

Mixed-potential Type NO2 Sensor Prepared with CuCr2O4-CuO Composite Sensing Electrode

Mixed Potential Type Sensor Using Stabilized Zirconia and La<sub>0.75</sub>Sr<sub>0.25</sub>Cr<sub>0.5</sub>Mn<sub>0.5</sub>O<sub>3</sub> Sensing Electrode for NO<sub>2</sub> Detection

An Amperometric NO2 Sensor Based on Nano-Structured La0.75Sr0.25Cr0.5Mn0.5O3−δ Prepared by Impregnating Method

Investigation on Impedencemetric-type NO_2 Sensor Based on La_(0.75)Sr_(0.25)Mn_(0.5)Co_(0.5)O_(3-δ) Sensing Electrode

Investigation on Impedencemetric-type NO2 Sensor Based on La0.75Sr0.25Mn0.5Co0.5O3-δ Sensing Electrode

Enhanced gas-sensing performance of SnO2/Nb2O5 hybrid nanowires

Mixed potential type sensor using stabilized zirconia and La 0.75Sr0.25Cr0.5Mn0.5O3 sensing electrode for NO2 detection

Preparation and NO_2 Gas Sensing Properties of La_(0.75)Sr_(0.25)Cr_(0.5)Mn_(0.5)O_3

An Amperometric NO2 Sensor Based on La10Si5NbO27.5 Electrolyte and Nano-Structured CuO Sensing Electrode.

Study of NO2 sensors based on La0.8Sr0.2Co0.2Fe0.8O3-δ/Ag biphasic composite sensing electrodes