Abstract:For resource reutilization, scrap tyres have long been investigated as an additive to concrete to form 'Rubcrete' for various applications and have shown promising results. However, the addition of rubber particles leads to the degradation of physical properties, particularly, the compressive strength of the concrete. In this study, a theoretical model was proposed to shed light on the mechanisms of decrease in compressive strength due to the addition of rubber particles as well as improvement in compressive strength through modification of particle surfaces. The literature suggests that the compressive strength can be improved by soaking the rubber particles in alkaline solution first to increase the inter-phase bonding between the rubber particles and cement. Instead, we discovered that the loss in compressive strength was due to local imperfections in the hydration of cement, induced by the addition of heterogeneous and hydrophobic rubber particles. Microscopic studies showed that the rubber particles disturbed the water transfer to create channels, which were prone to cracking and led to a loss in the compressive strength. Unexpectedly, no cracking was found along the surfaces of the rubber particles, indicating that the bonding strength between the rubber particles and cement phases was not the critical factor in determining the compressive strength. Therefore, a theoretical model was proposed to describe the water transfer in the Rubcrete specimens to explain the experimental data. In the model, the local water available for hydration (Q) is: Q = -A(slv)/6piv, where Q, A(slv), and v are mass flow rate (kg s(-1)), Hamaker constant (J), and dynamic viscosity (m2 s(-1)), respectively. By maximizing the quantity Q and, in turn, the Hamaker constant A(slv), the compressive strength could be improved. The Hamaker constant A(slv) for water film on rubber particle surfaces was smaller than that for the hydrated cement particles; the water transfer rate was lower in the presence of rubber particles because the Hamaker constant A(slv) for water film on rubber particle surfaces was smaller than that on the hydrated cement particles. Thus, the compressive strength of Rubcrete could be improved by increasing the Hamaker constant of the system. This was achieved by increasing the refractive indices of the solids (n(s)). The refractive indices of materials increase with increases in functional groups, such as OH and SH on the surface. The model provided a possible mechanism for the efficacy of treating rubber particles with NaOH in improving the compressive strength. By using NaOH solution treatment, an oxygen-containing OH group was formed on the rubber surface to increase the Hamaker constant of the system, leading to higher compressive strength. Based on this mechanism, a novel method for modification of the rubber particles was also proposed. In this process, the rubber particles were partially oxidized with hot air/steam in a fluidized bed reactor to produce the hydrophilic groups on the surface of the particles. Preliminary results obtained so far are promising in accordance with the theory.

Experimental Research on Abrasion Resistance and Predictive Model of High-Density Rubberized Concrete with High Strength

Probabilistic Models of Concrete Compressive Strength and Elastic Modulus with Rubber Aggregates

Experimental Investigation on the Dynamic Compressive Behavior of Rubberized Concrete

High-strain rate compressive behavior of Fiber-Reinforced Rubberized Concrete

Predicting Fatigue Damage Growth in Cement-Treated Base Layer Built with Construction and Demolition Waste

Experimental and numerical investigation on fracture characteristics of self-compacting concrete mixed with waste rubber particles

Impact of Rubber Content on Performance of Ultra-High-Performance Rubberised Concrete (UHPRuC)

Research on static mechanical properties of high-performance rubber concrete

RETRACTED: Experimental investigation and comparative machine-learning prediction of strength behavior of optimized recycled rubber concrete

Performance analysis and engineering application of waste rubber crumbs in concrete

Experimental study on strength and abrasion-resistance enhancement admixture

Optimization of Cohesive Parameters in the Interfacial Transition Zone of Rubberized Concrete Based on the Response Surface Method

Hybrid nonlinear regression model versus MARS, MEP, and ANN to evaluate the effect of the size and content of waste tire rubber on the compressive strength of concrete

Study on macro and micromechanical properties of polypropylene fiber reinforced rubber-based flexible energy-consuming concrete

Use of waste rubber as concrete additive

Numerical Simulation of the Effect of Freeze-Thaw Cycles on the Axial Compression Strength of Rubber Concrete

Experimental investigation on the impact resistance of rubber self-compacting concrete

Experimental Study of Rubberized Concrete Stress-Strain Behavior for Improving Constitutive Models

Experimental Investigation and Machine Learning Prediction of Mechanical Properties of Rubberized Concrete for Sustainable Construction

Optimization of recycled rubber self-compacting concrete: Experimental findings and machine learning-based evaluation

Mesoscopic Analysis of Rounded and Hybrid Aggregates in Recycled Rubber Concrete