Abstract:The enhancement of cryogenic plasticity for some aluminum alloys has attracted broad attention, which provides a new approach to the formability improvement of high-strength aluminum alloys. However, the hardening behavior and the ductility of aluminum alloys at cryogenic temperatures are very sensitive to the microstructure tempered at different conditions, with complex combination of GP zones, second phase precipitates, coarse and equilibrium phases. In this paper, three groups of tempered AA7075 aluminum alloy sheets are elaborately designed by means of different approaches, i.e., solution-treated (W), peak artificial aged (T6), and fast re-dissolved (FD) from T6, to investigate their cryogenic deformation behavior and failure mechanism. The effect on cryogenic plasticity of second phases, including the coarse particles in the matrix and the precipitate free zones (PFZs) accompanied by chain distributed particles along grain boundary, can be isolated by comparison among these three kinds of AA7075 alloys. The cryogenic mechanical properties of AA7075 sheets are evaluated by uniaxial tensile test, and the microstructure evolution observed by transmission electron microscope (TEM), scanning electron microscope (SEM) and laser confocal microscope (LCM). It shows that the enhancement of both ductility and continuous work hardening for W- and FD-tempered AA7075 sheets at cryogenic temperatures results from the uniformly distributed dislocations in the matrix of supersaturated solid solution (SSSS). The relatively low cryogenic ductility of AA7075-FD in comparison with AA7075-W results from the cracked η phases in the interior of grain, which has an increasing brittleness and high stresses on the particle due to the bypassing process at cryogenic condition. Furthermore, the undesirable early fracture of AA7075-T6 alloy during cryogenic deformation process is systematically illustrated from the aspect of interaction between dislocation and second-phase particles. Beside the cracked η phases in the interior of grains, defects also appear in the non-coherent interface between PFZ and the equilibrium η phase due to stain localization at grain boundary. As a result, AA7075-T6 alloy exhibits a ductile-brittle mixed fracture mode dominated by PFZ and the equilibrium η phase at grain boundary.

Uncovering the microstructural and precipitate evolution in the cryogenic temperature - Friction stir processed AA6xxx sheets

Investigation on variations of microstructures and mechanical properties along thickness direction of friction stir processed AA2014 aluminum alloy via ultra-rapid cooling

Microstructural Characterization of Friction-Stir Processed Ti-6Al-4V

Post-weld heat treatment effects on microstructure, crystal structure, and mechanical properties of donor stir–assisted friction stir welding material of AA6061-T6 alloy

Microstructure refinement, strengthening and ductilization mechanisms in Al–Mg–Mn–Er–Zr alloy with high Mn content by friction stir processing

Surface modification of Ti-6Al-4V alloy via friction-stir processing: Microstructure evolution and dry sliding wear performance

Microstructure transition and mechanical properties of friction stir processed CoCrFeMnNi high entropy alloy fabricated by laser powder bed fusion

Investigation on Microstructure Evolution of Mg-Gd-Zn-Zr Alloys During Friction Stir Processing by Liquid CO2 Cooling Assisted Stop Action

Cryogenic Deformation Behavior and Failure Mechanism of AA7075 Alloy Sheets Tempered at Different Conditions

Crystallographic texture evolution during friction stir processing of AA7075 alloy

Revealing the Effects of Friction Stir Processing on the Microstructural Evolutions and Mechanical Properties of As‐Cast Interstitial FeMnCoCrN High Entropy Alloy

Microstructure, Texture and Mechanical Properties of Friction Stir Processed Mg-14gd Alloys

Microstructure Evolution and Mechanical Properties of Friction Stir Welded Al–Cu–Li Alloy

Microstructure Characterization of the Stir Zone of Submerged Friction Stir Processed Aluminum Alloy 2219

Dynamic recrystallization and solute precipitation during friction stir assisted incremental forming of AA2024 sheet

Effect of Heat Treatment on the Microstructure, Mechanical Properties, and Corrosion Resistance of Friction Stir Processed Al-Zn-Mg-Cu-Sc-Zr Alloy

Microstructure Evolution and Grain Refinement in 2319 Aluminium Alloy Via Wire Arc Additive Manufacturing Coupled with Multi-Pass Friction Stir Processing

Microstructure of Multi-Pass Friction-Stir-Processed Al-Zn-Mg-Cu Alloys Reinforced by Nano-Sized TiB2 Particles and the Effect of T6 Heat Treatment

TEM characterization on microstructure of Ti–6Al–4V/Ag nanocomposite formed by friction stir processing

Influence of Friction Stir Spot Processing on Grain Structure Evolution and Nanomechanical Behavior of Cold-Sprayed Al Coating on Ti Substrate

Effect of Heat Treatment on Friction-Stir-Processed Nanodispersed AA7075 and 2024 Al Alloys