Abstract:The growing need for sustainable and low-carbon energy sources has led to significant research in alternative fuels. The majority of energy produced today comes from fossil fuels, which has led to enormous emissions of greenhouse gases. The direct combustion of fossil fuels produces syngas and hydrogen, which contribute to global warming. In contrast, the gasification process of biomass produces clean energy in the form of syngas and hydrogen. The biomass and plastic co-gasification has gained a lot of attention recently due to the challenges associated with gasifying biomass and plastic wastes separately. The broader objectives of this study are to alleviate these waste management problems and optimize the syngas LHV and H 2 content using co-gasification process. The synthesis gas is a crucial intermediary used to create chemicals and fuels for transportation. The hydrogen component of synthesis gas can also be utilized directly as fuel for hydrogen fuel cells, which produce electricity. This work employs Aspen simulator to analyze an optimum processing condition where the synthesis gas has the maximum feasible hydrogen content and calorific value which has not been investigated in the available literature so far. Aspen software is used in this study since it can be useful in figuring out reaction yield and performing parametric studies to optimize process conditions. It is found that the carbon dioxide emission sharply decreases as the proportion of plastic increases in co-gasification. The mole fractions of CO, H 2 and CO 2 that the current model predicts using experimental data on rice husk have average modeling errors of less than 8%, indicating a satisfactory fit with the experimental findings. Under 1 bar of pressure and a combined feed rate of 100 kg/h for both plastic and biomass, the simulation was run at temperatures between 550 °C and 1300 °C. When steam was added, the fraction of hydrogen increased by approximately a factor of two for a steam-to-biomass ratio (SBR) of 2. Following the addition of plastic to the feed, the amount of hydrogen in the produced gas rose for all temperatures. When 15% plastic is combined with the feed at 850 °C, carbon dioxide is reduced by roughly 60%. The results indicate significant increase in calorific value of the product as well as the hydrogen proportion—suggesting plastic addition as an excellent method to improve the LHV of biomass gasification.

Techno-economic Assessment of Co-gasification of Rice Husk and Plastic Waste As an Off-grid Power Source for Small Scale Rice Milling - an Aspen Plus Model

Techno-economic Analysis of a Biogas Driven Poly-Generation System for Postharvest Loss Reduction in a Sub-Saharan African Rural Community

Techno-Economic Analysis of a Cogeneration System for Post-Harvest Loss Reduction: A Case Study in Sub-Saharan Rural Community

Techno‐economic assessment on the implementation of biomass gasifier in conventional parboiling rice mills

Energy Efficiency and Life Cycle Assessment with System Dynamics of Electricity Production from Rice Straw Using a Combined Gasification and Internal Combustion Engine

Performance Analysis of Bio-Energy Based Power Generation System in Nigeria Using Rice Husk Feedstock

Off-Grid Electricity Generation Using Mixed Biomass Compost: A Scenario-Based Study with Sensitivity Analysis

Economics of Distributed Power Generation via Gasification of Biomass and Municipal Solid Waste

OPERATION AND ECONOMY ANALYSIS OF 1MW CIRCULATING FLUIDIZED BED FOR RICE HUSK GASIFICATION & POWER GENERATION SETS

Syngas and hydrogen production from co-gasification of rice husk biomass and plastic waste mixture using Aspen Plus

Harnessing biomass waste-to-energy for sustainable electricity generation: prospects, viability, and policy implications for low-carbon urban development

Design and operation of a CFB gasification and power generation system for rice husk

A feasibility analysis of distributed power plants from agricultural residues resources gasification in rural China

Rice husk reuse as a sustainable energy alternative in Tolima, Colombia

Techno-economic assessment of sugarcane bagasse pith-based briquette production and performance analysis of briquette feed gasifier-engine system

Co-gasification of rice husk and plastic in the presence of CaO using a novel ANN model-incorporated Aspen plus simulation

Utilization of Rice Husk in the CO2-Recycling Gasification System for the Effective Implementation of Bioenergy with Carbon Capture and Storage (BECCS) Technology

Unlocking the techno-economic potential of biomass gasification for power generation: Comparative analysis across diverse plant capacities

Co-gasification of rural solid waste and biomass in rural areas: Simulation and plant-scale process

Economic assessment of utilization of plastic waste via pyrolysis power plant as low-carbon thermal power station alternative in Sudan