Abstract:The microscopic dislocation slip and deformation of the machined surface layer of 304 stainless steel during turning leads to severe work hardening, and the study of the microstructural evolution of the surface layer of turned 304 stainless steel is of high importance to investigate microscopic plastic deformation and reduce work hardening. Most existing studies relating to the microstructural evolution of machined surfaces have used two-dimensional (2D) orthogonal cutting models. In this paper, we proposed a method to quickly build a three-dimensional (3D) bevel cutting finite element model and ABAQUS 3D cutting simulation models using temperature-displacement coupling algorithm, which can solve the problems of complex geometric modeling and low computational efficiency of ABAQUS 3D. In addition, a dislocation evolution modeling method was proposed through direct iterative optimization of intrinsic parameters, a subroutine of dislocation density evolution prediction model was written in accordance with finite element secondary development, and a joint simulation-based inverse identification method of dislocation evolution rate parameters was developed to minimize the error between simulated and experimental values of cutting forces. We compared the simulation results and the results of microstructure morphology analysis, verified the effectiveness of the inverse identification method and the dislocation density evolution prediction model, and then investigated the effect of dislocation evolution rate parameters α∗, β∗, k0 on the main cutting force, the microhardness, the dislocation density and the grain size. The microhardness changes of the cut surface were predicted using the microscopic dislocation deformation mechanism. By comparing the experimental data, we found that the predicted microhardness values of the machined surface at different cutting amounts were well consistent with the experimental data, thus verifying the credibility of the microhardness prediction model. Subsequently, the effect of cutting parameters on microhardness values, the average depth of slip zone, the equivalent plastic strain and the strain layer depth was analyzed.

A new approach to predict microhardness of two-phase in cutting S32760 duplex stainless steel

Microstructures-based Constitutive Analysis for Mechanical Properties of Gradient-Nanostructured 304 Stainless Steels

Research on microhardness prediction of 304 stainless steel turning based on dislocation density

Microhardness Prediction Based on a Microstructure-Sensitive Flow Stress Model During High Speed Machining Ti-6Al-4V

Prediction of critical cutting condition for onset of serrated chip in ductile metallic material using dynamic yield stress

Micromechanical Observation and Numerical Simulation for Local Deformation Evolution of Duplex Stainless Steel

A multi-barrier model assisted CAFE method for predicting ductile-to-brittle transition with application to a low-carbon ultrahigh-strength steel

Mechanism of δ → δ + γ phase transformation and hardening behavior of duplex stainless steel via sub-rapid solidification process

Study on the Deformation Behavior of Two Phases during the Low Cycle Fatigue of UNS S32750 Duplex Stainless Steel

Determination of the Minimum Chip Thickness and the Effect of the Plowing Depth on the Residual Stress Field in Micro-Cutting of 18 Ni Maraging Steel

Microstructure-Based Flow Stress Model to Predict Machinability of Inconel 718

New In Situ Imaging-Based Methodology to Identify the Material Constitutive Model Coefficients in Metal Cutting Process

Study on the Composition Design, Microstructure, Wear and Corrosion Resistant of Duplex Stainless Steels Based on Machine Learning

Evaluation of cutting edge K-form factor in milling of 316L stainless steel: a study based on FEM

Analysis and design of dual-phase steel microstructure for enhanced ductile fracture resistance

A Two-Step Approach to Predict Shear Band Development with Crystal Plasticity Finite Element Method (Cpfem)

Characterization of material strain and thermal softening effects in the cutting process

An investigation of phase boundary effect on the cutting force fluctuation in orthogonal micro-cutting of Ti6Al4V alloy

The effect of cutting fluid on high strain rate dynamic mechanical property and cutting force of ultra-high-strength steel

Experimental microstructure evolution and cutting simulation for dynamic mechanical behaviors of 18CrNiMo7-6 steel considering heat treatment conditions

Study on prediction model of cavitation erosion incubation period of duplex stainless steel surfacing layer in a benign medium