Abstract:High-performance manufacturing (HPM) is essential for high-quality equipment and parts manufacturing, which requires not only geometric accuracy but also control of surface integrity to satisfy functional performance. Surface topography and residual stress are important elements of surface integrity. However, they are always investigated individually, and their collaborative formation pattern has been ignored for a long time. In this study, surface topography will be measured by a 3D laser scanning microscope and analyzed from the perspective of spectral wavelength ( λ ) along with its corresponding amplitude. Whereas the residual stress (RS) is going to be analyzed by X-Ray diffraction and finite element (FE) model. Thereafter we introduce the formation pattern of both surface topography and RS. Hereby, simulated points clouds of machined surface topography are generated by superimposing the normally distributed random numbers that take into account the springback of the workpiece material response on tool kinematics and geometry. Furthermore, the RS is divided into mechanical loads induced ( RS M ) and thermal loads induce ( RS T ) according to the mechanism of formation, which were obtained in cutting speed (Y-direction) and feed direction (Z-direction) by the Mohr circle. Our experimental and numerical results showed that an increase in the feed rate (from 0.05 mm/r to 0.15 mm/r) significantly increases the surface roughness and cutting temperature. The increase in temperature increased the RS T by up to 286.1%, resulting in a reduction of compressive RS in Z-direction and an increase of tensile RS in Y-direction. Moreover, the increase in cutting speed (from 40 m/min to 80 m/min) results in a more regular surface and a reduction in surface roughness because of the smaller springback. At the same time, it also leads to a decrease of RS M in Z-direction and an increase of RS M in Y-direction. In addition, the increment in cutting speed leads to a minor increase in temperature and RS T (maximum increase of 47.0%). Combining the effects of RS M and RS T , RS in both directions increases slightly.

Evaluation of cutting edge K-form factor in milling of 316L stainless steel: a study based on FEM

Simulation of 3d Chip Shaping of Aluminum Alloy 7075 in Milling Processes

Numerical investigation of sequential cuts residual stress considering tool edge radius in machining of AISI 304 stainless steel

Evolution of residual stress when turning a fillet radius in stainless steel

A study on end mill tool geometry parameters for end milling of 316L: finite element analysis and response surface methodology optimization based on resultant cutting force

Finite Element Simulation on Face Milling of Austenitic Stainless Steel with Chamfered Tools

Numerical Modeling of the Effect of Cutting-Edge Radius on Cutting Force and Stress Concentration during Machining

Analysis of cutting tool geometry induced machining response, surface integrity and anisotropy relation of additively manufactured 316L stainless steel

Asymmetrical cutting-edge design of broaching tool based on FEM simulation

Numerical investigation on effect of rounded cutting edge radius in milling of ultra-high-strength steel 30Cr3SiNiMoVA

Cutting Forces and Chip Shaping When Finish Turning of 17-4 PH Stainless Steel under Dry, Wet, and MQL Machining Conditions

Research on Cutting Edge form Factor of Milling Tool after Drag Finishing Preparation Based on Discrete Element Method

An Fem Study on Residual Stresses Induced by High-Speed End-Milling of Hardened Steel Skd11

Finite element simulation and regression modeling of machining attributes on turning AISI 304 stainless steel

Finite Element Simulation of Influence of Tool Edge Radius in Micro-milling

Finite Element Analysis of Revolving Tip-Based Cutting Process

Machining performance evaluation and tool wear analysis of dry cutting austenitic stainless steel with variable-length restricted contact tools

[A Three-Dimensional Finite Element Analysis of 0.02 Taper 20# Stainless Steel K Files During Root Canal Instrumentation].

Collaborative formation pattern of surface topography and residual stress in hard turning of steels

Numerical Investigation on the Effect of Cutting-Edge Shape Factor on the Cutting Performance of Titanium Alloy

3D Coupled Thermo-Mechanical Simulation of Surface Roughness and Residual Stress in End Milling Aluminum Alloy