Abstract:Properties such as wide bandgap, higher electromechanical coupling, and low dielectric permittivity have propelled ScxAl1−xN as an advantageous material for optoelectronics and RF applications. ScxAl1−xN devices are challenging to fabricate because ScAlN films are complex to etch, especially with greater scandium concentrations. Our group has developed a procedure to etch ScxAl1−xN (x = 0.125, 0.20, 0.40) thin films (~ 730 nm thick), which results in vertical sidewalls that approach 85–90° (± 0.4°) and reduce the degree of the undercut. To maintain uniformity between various Sc compositions during the etching process, a nitrogen atmosphere was employed for high-temperature annealing, followed by immersion in a bath of tetramethyl ammonium hydroxide (TMAH) for wet etching. A 25% concentrated TMAH solution was used at 78–82 °C to etch down the ScxAl1−xN film layer. The etching rate of Sc0.125Al0.875N$${\mathrm{Sc}}_{0.125}{\mathrm{Al}}_{0.875}\mathrm{N}$$, Sc0.20Al0.80N$${\mathrm{Sc}}_{0.20}{\mathrm{Al}}_{0.80}\mathrm{N}$$, and Sc0.40Al0.60N$${\mathrm{Sc}}_{0.40}{\mathrm{Al}}_{0.60}\mathrm{N}$$ was found to be approximately, 365 nm/min, 243 nm/min, and 81 nm/min, respectively. Experimental results demonstrated that an identical etching profile can be obtained by TMAH vapor as well. We demonstrated how the annealing process recovers the deterioration introduced into the ScxAl1−xN by the ion-bombardment effect developed during the SiO2/SiNx hard mask dry etch step, ultimately preventing lateral etching. We have also reduced sidewall roughness of a post-etched ScxAl1−xN film with the combination of inductively coupled plasma etch, high-temperature annealing, and wet etching without affecting the sidewall verticality. Preliminary results of ongoing device fabrication that use this developed etch approach are also presented herewith to give an overview of the ongoing work.Graphical abstractOur group has developed a state-of-the-art procedure to etch ScxAl1−xN (x = 0.125, 0.20, 0.40) thin films (~ 730 nm thick), which results in vertical sidewalls that approach 85–90° (± 0.4°) and reduce the degree of the undercut. To maintain uniformity between various Sc compositions during the etching process, a nitrogen atmosphere was employed for high-temperature annealing, followed by immersion in a bath of tetramethyl ammonium hydroxide (TMAH) for wet etching. A 25% concentrated TMAH solution was used at 78–82 °C to etch down the ScxAl1−xN film layer. Experimental results demonstrated that an identical etching profile can be obtained by TMAH vapor as well. We demonstrated how the annealing process recovers the deterioration introduced into the ScxAl1−xN by the ion-bombardment effect developed during the SiO2/SiNx hard mask dry etch step, ultimately preventing lateral etching. We have also reduced sidewall roughness of a post-etched ScxAl1−xN film with the combination of inductively coupled plasma (ICP) etch, high-temperature annealing, and wet etching without affecting the sidewall verticality.

Research of etching process of Al0.8Sc0.2N based on ICP etching equipment

Preparation Technique Of Aln Piezoelectric Thin Film

Etching of scandium-doped aluminum nitride using inductively coupled plasma dry etch and tetramethyl ammonium hydroxide

Piezoelectric and elastic properties of Al0.60Sc0.40N thin films deposited on patterned metal electrodes

Vertical and Lateral Etch Survey of Ferroelectric AlN/Al1-xScxN in Aqueous KOH Solutions

A process study of electron beam nano-lithography and deep etching with an ICP system

Deposition, Characterization, and Modeling of Scandium-Doped Aluminum Nitride Thin Film for Piezoelectric Devices

High Quality Co-Sputtering AlScN Thin Films for Piezoelectric Lamb-Wave Resonators

The Preparation of Scaln(002) Alloy Thin Films Deposited on Si(100) Substrates by Dc Reactive Magnetron Sputtering

A Parametric Study of ICP-RIE Etching on a Lithium Niobate Substrate

Preparation, Characterization, and Application of AlN/ScAlN Composite Thin Films

High Rate Deposition of Piezoelectric AlScN Films by Reactive Magnetron Sputtering from AlSc Alloy Targets on Large Area

Advanced Etching Techniques of LiNbO3 Nanodevices

Theoretical and Experimental Study of High-Electromechanical-Coupling Surface Acoustic Wave Resonators Based on A-Plane (1120)al0.56sc0.44n Films

Effects of High-Temperature Thermal Annealing on the Crystal Structure and Phase Separation in Sputtered ScAlN Thin Films

Selective Dry Etching of GaAs/AlAs Based on SiCl4/SF6 Mixtures by ICP

Role of Oxygen on Structure and Piezoelectric Properties of Al0.65Sc0.35 N Thin Films

REACTION SIMULATION AND EXPERIMENT OF A Cl2/Ar INDUCTIVELY COUPLED PLASMA FOR ETCHING OF SILICON

Highly Selective Dry Etching of Gan over Algan Using Inductively Coupled Cl-2/N-2/O-2 Plasmas

Smooth Etching of Epitaxially Grown AlN Film by Cl2/BCl3/Ar-based Inductively Coupled Plasma

AlScN films prepared by alloy targets and SAW device characteristics