Abstract:Magnesium sheet metal alloys have a hexagonal close packed (hcp) crystal structure that leads to severe evolving anisotropy and tension-compression asymmetry as a result of the activation of different deformation mechanisms (slip and twinning) that are extremely challenging to model numerically. The low density of magnesium alloys and their high specific strength relative to steel and aluminum alloys make them promising candidates for automotive light-weighting but standard phenomenological plasticity models cannot adequately capture the complex plastic response of these materials. In this study, the constitutive plastic behavior of a rare-earth magnesium alloy sheet, ZEK100 (O-temper), was considered at room temperature, under quasi-static conditions. The CPB06 yield criterion for hcp materials was employed along with a non-associative flow rule in which the yield function and plastic potential were calibrated for a range of plastic deformation levels to account for evolving anisotropy under proportional loading. The non-associative flow rule has not previously been applied to magnesium alloys which require the use of flexible constitutive models to capture the severe anisotropy and its evolution with plastic deformation. The non-associative flow rule can provide the required flexibility by decoupling the yield function and plastic potential. For the associative flow rule, such flexibility can only be achieved by multiple linear transformations of the stress tensor resulting in expensive models for calibration and simulations. The constitutive model was implemented as a user material subroutine (UMAT) within the commercial finite element software, LS-DYNA, for general 3-D stress states along with an interpolation technique to consider the evolution of anisotropy based upon the plastic work. To evaluate the accuracy of the implemented model, predictions of a single-element model were compared with the experimental results in terms of flow stresses and plastic flow directions under various proportional loading conditions and along different test directions. Finally, to assess the predictive capabilities of the model, full-scale simulations of coupon-level formability experiments were performed and compared with experimental results in terms of far-field load-displacement and local strain paths. Using these experiments, the constitutive model was evaluated across the full range of representative stress states for sheet metal forming operations. It was shown that the predictions of the model were in very good agreement with experimental data.

Multi-Island Genetic-Algorithm-Based Approach to Uniquely Calibrate Polycrystal Plasticity Models for Magnesium Alloys

Numerical simulation of plastic behavior and meso inhomogeneous deformation in AZ31 Mg alloy

Dynamic plasticity of AZ31 magnesium alloy: Experimental investigation and constitutive modeling

Constitutive Modeling of Slip, Twinning and Detwinning for Mg Alloy and Inhomogeneous Evolution of Microstructure

Optimization of crystal plasticity parameters with proxy materials data for alloy single crystals

Application of an Evolving Non-Associative Anisotropic-Asymmetric Plasticity Model for a Rare-Earth Magnesium Alloy

Self-Consistent Crystal Plasticity Modeling of Slip-Twin Interactions in Mg Alloys

An Elastic–viscoplastic Crystal Plasticity Modeling and Strain Hardening for Plane Strain Deformation of Pure Magnesium

Multi-scale Modelling of Evolving Plastic Anisotropy During Al-alloy Sheet Forming

Assessment in Predictability of Visco-Plastic Self-Consistent Model with a Minimum Parameter Approach: Numerical Investigation of Plastic Deformation Behavior of AZ31 Magnesium Alloy for Various Loading Conditions

A Polycrystal Plasticity Based Thermo-Mechanical-dynamic Recrystallization Coupled Modeling Method and Its Application to Light Weight Alloys

Crystal plasticity modeling of the multiaxial ratchetting of extruded AZ31 Mg alloy

Crystal Plasticity Analysis of Plane Strain Deformation Behavior and Texture Evolution for Pure Magnesium

Simulation of Texture Evolution in Magnesium Alloy: Comparisons of Different Polycrystal Plasticity Modeling Approaches

Simulation of Magnesium Alloy AZ31 Sheet During Cylindrical Cup Drawing with Rate Independent Crystal Plasticity Finite Element Method

The strain rate sensitive and anisotropic behavior of rare-earth magnesium alloy ZEK100 sheet

Crystal Plasticity Model and Simulations for Single Crystal Magnesium

Multiscale Mechanical Behavior and Microstructure Evolution of Extruded Magnesium Alloy Sheets: Experimental and Crystal Plasticity Analysis

Crystal plasticity based modeling of grain boundary sliding in magnesium alloy AZ31B sheet

Controlling the Plastic Anisotropy of Magnesium Alloy by Tailoring the Grain Size and Yttrium Content

Crystal plasticity modeling of low-cycle fatigue behavior of an Mg-3Al-1Zn alloy based on a model, including twinning and detwinning mechanisms