Abstract:Using Atomsk and LAMMPS to construct nine bicrystal Mg models with preset voids and symmetric tilt grain boundaries, tensile simulations were performed at the same rate. The results showed that as the symmetric tilt grain boundary angle increased from 20° to 30°, the yield stress decreased from 2.28 to 1.42 GPa. Based on the plastic deformation and stress–strain curves, the nine bicrystal magnesium models with different symmetric tilt grain boundaries can be divided into two groups: the first group ranges from 20° to 40°, and the second group from 45° to 80°. A representative case is selected from each group. In the first group of models, the main modes of plastic deformation are grain boundary migration, basal dislocation slip, and stacking faults; whereas in the second group, there is a higher number of basal dislocation slips, leading to a greater quantity of stacking faults, and thus a stronger capacity for plastic deformation.2 A twin‐crystal magnesium (Mg) model with 9 different symmetric tilt grain boundary (STGB) angles (20°–80°) with preset nanohole defects is established by atomsk and lammps software. The mechanical behavior of grain boundary (GB) angles on twin‐crystal Mg with cavity defects and its cavity evolution are simulated by the molecular dynamics method with embedded atomic potential, and the plastic deformation mechanism is revealed. The results show that the yield stress decreases with the increase of the STGB Angle during the stretching process. When the GB Angle increases from 20° to 80°, the yield stress decreases from 2.28 to 1.42 Gpa. This is because the larger the STGB Angle is, the larger the Schmidt factor is, and the easier it is to start dislocation slip during the stretching process. On the other hand, the larger the Angle of STGB, the more the number of atomic voids at the interface, and the more the number of dislocation nucleation points. The larger the Angle of STGB, the lower the strength of twinning Mg but the better the plasticity to avoid fracture. The plastic deformation mechanism mainly includes the nucleation of Shockley incomplete dislocation at STGBs, dislocation slip generates stacking faults (SFs), GB migration, and base plane dislocations.

Crystal Plasticity Model and Simulations for Single Crystal Magnesium

Crystal Plasticity Behavior of Single-Crystal Pure Magnesium under Plane-Strain Compression

Crystal plasticity-based finite element modeling of twin transmission across grain boundaries in magnesium

Plastic deformation of magnesium single crystal: a crystal plasticity coupled twinning phase field simulation

Grain growth-induced strain softening in nanocrystalline magnesium: experiments and modelling

Comparison of three state-of-the-art crystal plasticity based deformation twinning models for magnesium alloys

Self-Consistent Crystal Plasticity Modeling of Slip-Twin Interactions in Mg Alloys

Efficient numerical strategies for an implicit volume fraction transfer scheme for single crystal plasticity including twinning and secondary plasticity on the example of magnesium

Crystal plasticity finite element modeling of twin band formation and evolution together with the macroscale mechanical responses of hexagonal metals

Deformation Analysis of Magnesium Alloy Based on Crystal Plasticity Theory

Dynamic plasticity of AZ31 magnesium alloy: Experimental investigation and constitutive modeling

On the Plasticity and Deformation Mechanisms in Magnesium Crystals

Multiscale Mechanical Behavior and Microstructure Evolution of Extruded Magnesium Alloy Sheets: Experimental and Crystal Plasticity Analysis

Finite strain crystal plasticity-phase field modeling of twin, dislocation, and grain boundary interaction in hexagonal materials

Crystal plasticity modeling of low-cycle fatigue behavior of an Mg-3Al-1Zn alloy based on a model, including twinning and detwinning mechanisms

Crystal plasticity based modeling of grain boundary sliding in magnesium alloy AZ31B sheet

A continuum description of nonlinear elasticity, slip and twinning, with application to sapphire

Study on the Plastic Deformation Mechanism of Void‐Containing Twin‐Crystal Magnesium with Symmetric Tilt Grain Boundary Angles

On the interaction of precipitates and tensile twins in magnesium alloys

Characterizing microscale deformation mechanisms and macroscopic tensile properties of a high strength magnesium rare-earth alloy: A combined experimental and crystal plasticity approach

Anomalous Hardening in Magnesium Driven by a Size-Dependent Transition in Deformation Modes