Abstract:High molecular weight polyether polyols are widely used. However, there is not only a large risk of reaction heat, but also a long reaction time in its traditional production process by using the semi-continuous reactor. The microchannel reactor（MCR） has the characteristics of high heat transfer efficiency and process safety,but the viscous material and high reaction heat release make it difficult to produce the high molecular weight polyether polyols. In this work, using double metal complex（DMC） as catalyst and n-hexane as solvent, the ringopening polymerization of propylene oxide（PO） was carried out in MCR. Polypropylene glycol（PPG） with molecular weight ranging from 2000 to 8000 was prepared. Effects of reaction conditions, such as flow rate, channel length,reaction temperature and feed policy, were investigated. It has been found that when the residence time is long enough, the molecular weight of the produced PPG is basically equal to the theoretical molecular weight. When the flow rate of initiator is fixed, an increase in flow rate of monomer will result in the molecular weight distribution（MWD） first widened and then narrowed. If the tube length is longer, the molecular weight is larger and the MWD is wider. If the temperature increases, the induction period of the polymerization can be shortened. Using the segmented feed, it is easier to prepare high molecular weight PPG with higher conversion than using the single feed, but the MWD is wider. These rules can be explained from the mechanism of PO ring-opening polymerization catalyzed by DMC and micro-mixing strength of materials in MCR. The lower the micro-mixing strength, and the smaller the rate ratio of chain transfer to chain propagation in polymerization, the wider the molecular weight distribution is.

Molecular Weight Distribution in Ring‐Opening Polymerization of Propylene Oxide Catalyzed by Double Metal Complex: A Model Simulation

Preparation of high molecular weight polypropylene glycol in microchannel reactor

Modeling of Molecular Weight and Copolymer Composition Distributions for Ethylene‐propylene Solution Copolymerization

Ring-Opening Polymerization of Propylene Oxide by Double Metal Complex in Micro-Reactor

Simulation on relative molecular mass distribution of LDPE tubular reactor

Theoretical Study on the High Polymer Molecular Weight of Heteroatom-Substituted Constrained Geometry Catalyst

Modeling of the Molecular Weight Distribution and Short Chain Branching Distribution of Linear Low-Density Polyethylene from a Pilot Scale Gas Phase Polymerization Process

Mathematical Modeling of the Molecular Weight Distribution of Polypropylene Produced in a Loop Reactor

Modeling of Sequence Length Distribution for Olefin Copolymerization with Vanadium‐Based Catalyst

Simulation And Optimization Of The Molecular Weight Distribution In A Non-Ideal Polymerization Reactor

A Segment Probability Method for Calculating the Molecular Weight Distributions of Linear Polycondensates in a Continuous Reactor

Modeling and optimization of polymer molecular weight distribution based on Kriging method

Modeling of Molecular Weight Distribution of Propylene Slurry Phase Polymerization on Supported Metallocene Catalysts

Experiment and Simulation on Styrene Polymerization with Linear Bifunctional Initiator 2,5-Dimethyl-2,5-di(2-ethylhexoylperoxy)hexane (Dmdehph)

Molecular Weight Distribution of Branched Polymers: Comparison between Monte Carlo Simulation and Flory-Stockmayer Theory

Kinetic Parameter Estimation for Linear Low-Density Polyethylene Gas-Phase Process from Molecular Weight Distribution and Short-Chain Branching Distribution Measurements

Drag Reduction and Degradation of Binary Polymer Solutions

Synthesis of PP with broad molecular weight distribution by multiple adding-withdrawing H_2 during polymerization process

Kinetic Analysis of "living" Polymerization Processes Exhibiting Slow Equilibria. 2. Molecular Weight Distribution for Degenerative Transfer (direct Activity Exchange Between Active and "dormant" Species) at Constant Monomer Concentration

Molecular Weight Distribution of a Living Polymer Generated from a Bifunctional Initiator with Non-Equal Initiation Rate Constants

Ring-opening Polymerization of Propylene Oxide Catalyzed by Fe-Zn Double Metal Cyanide Catalyst and Its Synthesis