Abstract:The missile launched by the conventional artillery is accelerated by the gas pressure, while the electromagnetic launched missile is accelerated by the electromagnetic force. Accordingly, there are three main differences between them. Firstly, as for the electromagnetic launch, when the muzzle velocity is precisely controlled, the driving current applied on the rail changes according to the difference between the desired and the measured velocity1, resulting in the change of the force acting on the missile more complex. Secondly, the electromagnetic launched missile reaches the maximum acceleration within a shorter time, and keeps it for a longer time. Thirdly, in the electromagnetic launching process, the missile is accelerated by the armature2. When the launching process is completed, in order to improve the controllability and flexibility of the missile, the missile must be separated from the armature. Therefore, the missile is not fixed with the armature together. When there is a gap between the armature and the missile, at the beginning of the launching process, the armature accelerated by the strong electromagnetic force obtains a large momentum in quite a short time, so there is an impact after the contact of the armature and the missile, which does not exist in the conventional artillery. As a result, the anti-shock design of the electromagnetic launched missile against high overload becomes very difficult. In this paper, an anti-shock device design method, taking into account the single-degree-of-freedom system dynamics and the modal analysis, was proposed. Through reasonable simplification, the finite element model including printed circuit and other components was created using the finite element analysis software ANSYS/LS-DYNA. And then the anti-shock performance of the important components of the device under impact circumstance was researched through the shock dynamic response results obtained. Based on theoretical analysis and numerical simulation, the anti-shock performance of the electronic devices on electromagnetic launched missile is improved through several methods, including adding damping elements, raising the stiffness of the devices, change of the distribution of electronic components, and etc. Comparing the different methods above, the optimization design is proposed, which could improve the anti-shock performance a lot. The research in this paper would be a reference in improving the anti-shock design of the electromagnetic launched missile.

Research on Ignition Time Control of Initiating Explosive Device Based on Magnetoelectric Energy Converter

Improvement of electromagnetic energy transfer efficiency for radio frequency explosive magnetic flux compression generator

Preliminary experimental study on the mechanisms of explosion-electric coupling

Penetration and ignition of new magnetoelectric self-powered small-caliber multi-effect penetrator obliquely impacting aluminum target

Design of Multi-point Synchronous Initiation Circuit for Shaped Charge

Study on Electrical Explosion Mechanism and Ignition Characteristics of Copper and Aluminum Powder under Ignition Solid Propellant

Research on a MEMS pyrotechnic with a double-layer barrier safety and arming device

Study on Phenomenon and Mechanism of Overvoltage in Electrothermal-Chemical Launch

Design and Performance of a Micro-Scale Detonation Train with a Built-in Pyrotechnic MEMS-based Safety and Arming Device

Ignition Characteristics of Energetic Nichrome Bridge Initiator Based on Al/CuO Reactive Multilayer Films under Capacitor Discharge and Constant Current Conditions

Experimental Investigation on the Enhancing Effect of Reactive Materials on Explosion Fireballs and Shock Waves of Composite Charges

Ignition Performance of Cu-wire Electrical Explosion Plasma on Energetic Materials

Discussion on Topologies of Quick Response IPPS Suitable for Closed-Loop Control of EML

Design and Experimental Research of Ultra-High-Speed Electromagnetic Rail Launch Device

Research on Indirect Charging Radio Frequency Explosive Magnetic Flux Compression Generator

Design, Fabrication, and Characterization of a Laser-Controlled Explosion-Initiating Device with Integrated Safe-and-Arm, EMP-Resistant, and Fast-Acting Technology Based on Photovoltaic Power Converter

PPPS-2013: Anti-shock Analysis of the Electromagnetic Launched Missile

Experimental study on explosion dispersion process of a multi-layer composite charge under different initiation modes

THE EXPERIMENTAL RESEARCH OF PLASMA IGNITER BASED ON THE LOAD RESONANCE

The Auto‐Ignition Behaviors and Thermal Safety of the Composite Modified Double Base Propellants under Rapid Heating

Tuning combustion and energy in hydroxylammonium nitrate (HAN)-based electrically controlled solid propellant