Abstract:Development of metallic glasses is hindered by the difficulties in manufacturing bulk parts large enough for practical applications. Spark plasma sintering (SPS) has emerged as an effective consolidation technique in the formation of bulk metallic glasses (BMGs) from melt-spun ribbons. In this study, Mg65Zn30Ca5 melt-spun ribbons were sintered at prolonged sintering times (15 min to 180 min) via SPS under a pressure of 90 MPa and at a temperature of 150 °C (which is below the crystallization temperature), to provide an insight into the influence of sintering time on the consolidation, structural, and biodegradation behavior of Mg-BMGs. Scanning Electron Microscopy was used to characterize the microstructure of the surface, while the presence of the amorphous phase was characterized using X-ray diffraction and Electron Backscatter Diffraction. Pellets 10 mm in diameter and height with near-net amorphous structure were synthesized at 150 °C with a sintering time of 90 min, resulting in densification as high as 98.2% with minimal crystallization. Sintering at extended durations above 90 min achieved higher densification and resulted in a significant amount of local and partial devitrification. Mechanical properties were characterized via compression and microhardness testing. Compression results show that increased sintering time led to better structural integrity and mechanical properties. Notably, SPS150_90 displayed ultimate compressive strength (220 MPa) that matches that of the cortical bone (205 MPa). Corrosion properties were characterized via potentiodynamic polarization with Phosphate Buffered Solution (PBS). The results suggest that the sintered samples have significantly better corrosion resistance compared to the crystalline form. Overall, SPS150_90 was observed to have a good balance between corrosion properties (10× better corrosion resistance to as-cast alloy) and mechanical properties.

Solid state recycling of Mg-Gd-Y-Zn-Zr alloy chips by spark plasma sintering

Consolidation behavior of Mg–10Gd–2Y–0.5Zr chips during solid-state recycling

Solid-state recycling of AZ91D magnesium alloy chips

Comparison Between Spark Plasma Sintering and Hot Extrusion for Solid-State Recycling of Al-Si-Cu-Fe Alloy Chips

Integrated Extrusion–Shear Forming Process of the Solid-State Recycled AZ80 Magnesium Alloy Via Hot Press Sintering

Effect of Extrusion Temperature on Microstructure and Mechanical Properties of Mg–Al–Zn Alloy Prepared by Solid‐State Recycling of Mixed Waste Chips

In-situ 14H-LPSO reinforced GW93 alloy prepared from the recycling of discard components by rapid-solidification plus hot press sintering technique

Microstructure and mechanical properties of Mg–10Gd–2Y–0.5Zr alloy recycled by cyclic extrusion compression

Mechanical Properties and Corrosion Resistance of Mg–10Gd–2Y–0.5Zr Alloy by Hot Extrusion Solid-State Recycling

Microstructure and high tensile strength of Mg–10Gd–2Y–0.5Zr alloy by solid-state recycling

Solid-State Synthesis of SiC Particle-Reinforced AZ91D Composites: Microstructure and Reinforcement Mechanisms

Microstructures and Mechanical Properties of Mg-Gd-Zn-Zr Alloys Prepared by Spark Plasma Sintering

An Optimization Approach for Hot Compaction Technology of Mg–10Gd–2Y–0.5Zr Alloy During Solid-State Recycling

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Study on hot deformation behavior and dynamic recrystallization mechanism of recycled Al–Zn–Mg–Cu alloy

Microstructure and mechanical properties of AZ31B magnesium alloy prepared by solid-state recycling process from chips

Microstructure evolution of hot pressed AZ91D alloy chips reheated to semi-solid state

Influence of friction stir processing and aging heat treatment on microstructure and mechanical properties of selective laser melted Mg-Gd-Zr alloy

Enhancing Mechanical and Biocorrosion Response of a MgZnCa Bulk Metallic Glass through Variation in Spark Plasma Sintering Time

Recycling of Az91 Mg Alloy Through Consolidation of Machined Chips by Extrusion and Ecap

Enhanced Mechanical Properties of a Chip-Based Al-Si-Cu-Fe Alloy with an In-Situ Emulsion Decomposition Recycled by Solid-State Processing