Abstract:The Mg-11Gd-2Zn-0.4Zr (GZ112K, wt.%) alloys fabricated by selective laser melting (SLM) still contain some hard and brittle beta-(Mg,Zn)(3)Gd eutectic phase with an area fraction of 4.86% despite the ultra-fast cooling rate of SLM process, so post heat treatment is necessary. The effects of different solution conditions and aging heat treatment on microstructure and mechanical properties of the SLMed GZ112K alloys were systematically analyzed. The results show that the optimized solution condition (400 degrees C x 12 h) for the SLMed GZ112K alloys can not only transform hard and brittle beta-(Mg,Zn)(3)Gd eutectic phase into relatively softer lamellar 14H type long period stacking order (LPSO) structure leading to the improved elongation (EL) of the SLM-T4 alloys, but also retain the fine grains of the SLMed GZ112K alloys to a large extent with a small average grain size of 3.1 mu m in the SLM-T4 state contributing to the high yield strength (YS) of the SLM-T4 and SLM-T6 GZ112K alloys. After peak aging heat treatment, basal gamma ' precipitates or lamellar 14H-LPSO structure and dense prismatic elliptical 13 ' precipitates coexist in the SLM-T6 GZ112K alloys. As a result, the SLM-T6 GZ112K alloys exhibit YS of 343 +/- 9 MPa, ultimate tensile strength (UTS) of 371 +/- 4 MPa and EL of 4.0 +/- 0.05%, while those of the SLMed GZ112K alloys are 332 +/- 3 MPa, 351 +/- 5 MPa and 8.6 +/- 1.0%. The ultra-high YS of SLM-T6 GZ112K alloys results from the fine grain strengthening, the precipitation strengthening from 13 ' aging precipitates, the secondary phase strengthening from LPSO structure and X phase and the extra composite strengthening from the coexistence of basal and prismatic precipitates. The findings indicate that appropriate post heat treatment is an effective scheme for modifying microstructure and mechanical properties of the SLMed alloys.

Microstructures and Mechanical Properties of Mg-Gd-Zn-Zr Alloys Prepared by Spark Plasma Sintering

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Microstructures and Mechanical Properties of Mg-10Gd-3Y-2Zn-0.5Zr Alloy

Effect of Heat Treatment on Microstructure Evolution and Mechanical Properties of Selective Laser Melted Mg-11Gd-2Zn-0.4Zr Alloy

Fabrication of High-Strength Mg-Gd-Zn-Zr Alloy Via Selective Laser Melting

Microstructure and Mechanical Properties of Mg-12Gd-2Y-Sm-0.5Zr Alloy

Microstructure and mechanical properties with various pre-treatment and Zn content in Mg-Gd-Y-Zn alloys

Microstructure and Mechanical Properties of Mg–Gd–Y–Zn–Zr Alloy Sheets Processed by Combined Processes of Extrusion, Hot Rolling and Ageing

Effects of Zn and Gd Contents and Their Ratios on Microstructure and Mechanical Properties of As-Cast and As-Extruded Mg−8Li Alloys

Effect of Zn Concentration on the Microstructures and Mechanical Properties of Extruded Mg–7Y–4Gd–0.4Zr Alloys

Microstructures and Mechanical Properties of the Mg–4.5Zn–xGd (x = 0, 2, 3 and 5) Alloys

Effect of Gd Content on Microstructure and Mechanical Properties of Mg-xGd-Zr Alloys Via Semicontinuous Casting

Effects of Gd and Zr Additions on the Microstructures and High-Temperature Mechanical Behavior of Mg–Gd–Y–Zr Magnesium Alloys in the Product Form of a Large Structural Casting

The Research of Microstructure and Mechanical Properties of Mg–7Gd–3Y–1Nd–0.5Zn–0.5Zr (wt%) Alloy

Effects of extrusion process on microstructure, precipitates and mechanical properties of Mg-Gd-Y-Zr-Ag alloys

Microstructure and mechanical properties of Mg-Gd-Zn-Zr alloy after hot extrusion

Effect of Zn/(Gd+Y) ratio on the microstructure evolution and mechanical properties of Mg-Gd-Y-Zn-Zr alloy

Microstructure and mechanical properties of high strength Mg−15Gd−1Zn−0.4Zr alloy additive-manufactured by selective laser melting process

The Effect of Gd and Zn Additions on Microstructures and Mechanical Properties of Mg-4sm-3nd-Zr Alloy

Microstructure and Mechanical Properties of Mg–3.0Y–2.5Nd–1.0Gd–x Zn–0.5Zr Alloys Produced by Metallic and Sand Mold Casting