Abstract:In this study, AA7075 sheets were processed by cryorolling and room-temperature rolling respectively, and subsequent aging. The microstructure evolution and mechanical properties of AA7075 sheets were investigated by hardness measurements, tensile tests, X-ray diffraction, scanning electron microscopy and transmission electron microscopy. Results show that with the rolling reduction ratio of 80%, the room-temperature rolled samples had massive edge cracks, while the cryorolled samples were in good shape and without any cracks. The improved ductility of materials in cryogenic environments, the reduced precipitation and the absence of shear bands in sheets during cryorolling contributed to the reduced edge cracks. Compared to solution treated samples, the yield strength and ultimate tensile strength of cryorolled samples were increased by 155% and 44%, respectively, and the elongation decreased as a loss, which is obviously better than that of room-temperature rolled samples. After the subsequent aging treatment, the strength and ductility of the rolled samples were simultaneously improved, the yield strength of cryorolled + peak-aged sample was increased by 44 MPa and the elongation was increased by 68% compared with those of the cryorolled samples. Compared with room-temperature rolled + peak-aged samples, the strength of cryorolled + peak-aged sample was higher, and the elongation to failure and uniform elongation were increased by 58% and 72%, respectively. Numerous nanosized GP zones and η' phases were precipitated after aging, and the precipitation strengthening is the main contributor to the strength enhancement of the samples after aging. The improved ductility of cryorolled + peak-aged samples is mainly due to the combined effect of dislocation annihilation, uniform deformation and fine precipitates in them.

Microstructural Evolution and Mechanical Properties of Ultrafine‐Grained Ti Fabricated by Cryorolling and Subsequent Annealing

Microstructure Evolution Through Cryogenic Rolling of Ultra-High Purity Titanium Produced by Electron Beam Melting

High strength and toughness of Ti–6Al–4V sheets via cryorolling and short-period annealing

Grain refinement and phase transformation of pure titanium foils during asymmetrical rolling

Microstructure Evolution and Mechanical Properties of Pure Ti Alloy Sheet Fabricated by Double-Side Corrugated Rolling

Work Hardening Behavior and Microstructure Evolution of a Cu-Ti-Cr-Mg Alloy during Room Temperature and Cryogenic Rolling

Evolution of microstructure and mechanical properties during short-time annealing of a hard-plate rolled 2 vol% TiC p /near-β titanium matrix composite

Cryorolling impacts on microstructure and mechanical properties of AISI 316 LN austenitic stainless steel

Mechanical property enhancement and microstructure evolution of an Al-Cu-Li alloy via rolling at different temperatures

Microstructural evolution and cryogenic-normal temperature deformation behavior of the near-α titanium alloy TA15 fabricated by laser powder bed fusion

Effect of Post-ECAP Annealing on the Microstructure and Mechanical Properties of Commercially Pure Titanium

Microstructural Evolution Induced Mechanical Property Enhancement in Cryogenically Rolled Ce‐Modified SAF2507 Super Duplex Stainless Steel

Low temperature mechanical behavior of fine- and ultrafine-grained 304 austenitic stainless steel fabricated by cryogenic-rolling and annealing

Tailoring the Microstructure to Enhance the Cryogenic Mechanical Properties of a Fe–34.5mn–0.04c Steel

Effect of Cryorolling and Ageing on the Microstructure and Mechanical Properties of Al 7085 Alloy

The Effect of Annealing and Cryogenic Treatment on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy

Evolution of Microstructural and Mechanical Properties during Cold-Rolling Deformation of a Biocompatible Ti-Nb-Zr-Ta Alloy

A novel cryogenic rolling method for commercially pure titanium sheets featuring high strength and ductility

Static Recrystallization Behavior and Texture Evolution during Annealing in a Cold Rolling Beta Titanium Alloy Sheet

Achieving High Strength and Tensile Ductility in Pure Nickel by Cryorolling with Subsequent Low-Temperature Short-Time Annealing

Edge-crack free and high mechanical properties of AA7075 sheets by using cryorolling and subsequent aging