Abstract:In dentistry, the most commonly used implant materials are CP-Titanium Grade 4 and Ti-6Al-4V ELI, possessing comparably high Young's modulus (>100 GPa). In the present study, the second-generation titanium alloy Ti-13Nb-13Zr is investigated with respect to the production of advanced dental implant systems. This should be achieved by the fabrication of long semi-finished bars with high strength and sufficient ductility to allow the automated production of small implants at low Young's modulus (<80 GPa) to minimize stress shielding, bone resorption, and gap formation between the bone and implant. In addition, bacterial colonization is to be reduced, and bone adhesion is to be enhanced by adjusting the microstructure. To do so, a dedicated thermo-mechanical treatment for Ti-13Nb-13Zr has been developed. This includes the adaption of equal channel angular swaging, a modern process of severe plastic deformation to continuously manufacture nanostructured materials, to Ti-13Nb-13Zr and short-time recrystallization and ageing treatments. In particular, two-pass equal channel angular swaging at a deformation temperature of 150°C and a counterpressure of 8 MPa has successfully been used to avoid shear band formation during deformation and to produce long Ti-13Nb-13Zr bars of 8 mm diameter. During recrystallization treatment at 700°C for 10 min followed by water quenching, a sub-micron-size primary α-phase in a matrix of α″-phase was developed. Subsequent ageing at 500°C for 1 h leads to martensite decomposition and, thus, to a homogeneously nanostructured microstructure of α- and β-phase with substructures smaller than 200 nm. The resulting mechanical properties, especially the ultimate tensile strength of more than 990 MPa, fulfill the requirements of ASTM F1713 at Young's modulus of 73 GPa. Biological investigations show promising results in reducing bacterial biofilm formation and increased cell proliferation of osteoblasts compared to CP-Titanium Grade 4 and Ti-6Al-4V ELI, especially, if etched surfaces are applied.

Development and Characterization of Β‐type Ti‐Zr‐Nb‐Sn Dental Implant Materials

Development and characterization of beta-type Ti-Zr-Nb-Sn dental implant materialsEntwicklung und Charakterisierung von Implantatwerkstoffen aus beta-TiZrNbSn-Dentallegierung

Development and properties of dental Ti–Zr binary alloys

New Zr-25Ti-xMo alloys for dental implant application: Properties characterization and surface analysis.

The structure and mechanical properties of as-cast Zr–Ti alloys

Nanostructured Ti-13Nb-13Zr alloy for implant application-material scientific, technological, and biological aspects

Β-Type Ti-10Mo-1.25Si-xZr Biomaterials for Applications in Hard Tissue Replacements.

Biocompatibility Evaluation of a Newly Developed Ti–Nb–Zr–Ta–Si Alloy Implant

Cytocompatibility of Ti–xZr Alloys As Dental Implant Materials

Microstructures and mechanical properties of Ti_(30)Nb_5Ta_6Zr alloy

Mechanical and biological properties of Ti–(0–25 wt%)Nb alloys for biomedical implants application

Novel Biocompatible Zr-Based Alloy With Low Young'S Modulus And Magnetic Susceptibility For Biomedical Implants

Nb-Ti-Zr Alloys for Orthopedic Implants

Novel Biocompatible Zr-Based Alloy with Low Young’s Modulus and Magnetic Susceptibility for Biomedical Implants

Effects of Zr Addition on the Microstructural Evolution, Mechanical Properties, and Corrosion Behavior of Novel Biomedical Ti-Zr-Mo-Mn Alloys.

Investigation on Near-β Titanium Alloy Ti-5Zr-3Sn-5Mo-15Nb for Surgical Implant Materials

Novel Ultrafine-grained β-type Ti-28Nb-2Zr-8Sn Alloy for Biomedical Applications.

Design of Low Elastic Modulus Ti–Nb–Zr Alloys for Implant Materials

Influence of Zr Content on Microstructure and Mechanical Properties of Implant Ti–35Nb–4Sn–6Mo–xZr Alloys

Cytocompatibility, Stability and Osteogenic Activity of Powder Metallurgy Ta-xZr Alloys As Dental Implant Materials

Study of the Surface Wear Resistance and Biological Properties of the Ti–Zr–Nb–Sn Alloy for Dental Restoration